I need dataset for recommandation system?

Hi every body I need to collect datasets from different source to work on recommendation system algorithms, could you advise me how collect data?

27 February 2021 7,063 7 View

How to build .cks file (chemkin file) in ANSYS-Forte for hydrogen-diesel dual fuel?

Dear all, I'm trying to simulate the combustion of hydrogen diesel in dual fuel mode in ANSYS-Forte. I have kinetic reaction mechanisms file( .txt) but in order to build the .cks file in the...

28 December 2020 1,570 3 View

How to measure both Sulfites and Sulfates Ions In water?

Could you please help me to know a very simple method to measure the amount of Sulfite (SO3) and Sulfate (SO4) ions in the water? (titration preferred)

27 December 2020 9,350 4 View

How can I fix the `engine error` with no error message in Lumerical DEVICE software when it only shows directories instead of error message?

When I run my simulation in Lumerical DEVICE, it shows an error entitled `engine error` after reaching the simulation to 100 percent. When I right-click and chose 'job details`, it only shows the...

22 October 2020 4,973 1 View

What are the effect of data spread on Random Forest model performance?

Since I am using the Random Forest model in R to predict LST (land surface temperature) from actual LST, I realized that model performance is better in lower Average LSTs, thus I wanted to extract...

14 October 2020 9,278 2 View

How can I get rid of much amount of solvent which is needed for the reaction to make film by film applicator?

Indeed, I want to make a very thin film (50 microns) of PU on the steel surface as a coat. for the reaction, much amount of CHCl3 is needed to dissolve one of the reagents to participate in the...

12 October 2020 748 3 View

What is the major meaning of PCs in Principal Component Analysis?

I am using PCA to extract major meaningful data from many different parameters that are embedded in my remote sensing satellite imagery. I know that PCA is a dimension reduction model and the...

13 September 2020 7,596 7 View

How do I get the number of water molecules in a carbon nanotube?

12 September 2020 886 6 View

What is the best book to teach entrepreneurship to primary students?

What is the best book to teach entrepreneurship to primary students?

07 September 2020 6,757 3 View

Is there any specific Proportion for training and testing set for remote sensing images?

Can I use one Sentinel image for training my model and another one for testing? Since i have two or three images, I wanted to use one or two image for training and the rest for test. However, I...

20 August 2020 9,028 6 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View