Where can I learn to make a conformal meshing for a multibody part?

More Pedro Barrios's questions See All

Absorption coefficient of methane?

Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?

06 August 2024 980 5 View

How are Large Models Exploring and Outputting Knowledge Understanding in Specific Content Areas, and What Does Academic Research Say About It?

Hello everyone！ I am currently exploring the performance of large models in understanding knowledge in specific domains, and attempting to construct a knowledge framework similar to what...

05 August 2024 5,729 2 View

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity?

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...

03 August 2024 5,358 0 View

How do i get an account to upload my published papers?

need to open an account to upload my published papers

01 August 2024 9,255 1 View

What is the problem with these tissue culture plants?

All plants are green but some of these plants becomes yellow. I did not found any reason. Please help me to find out the real problem.

01 August 2024 589 4 View

How to correctly use the UTE and ZTE pulse sequences in Bruker's ParaVision software?

I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...

01 August 2024 9,227 1 View

Is artifacts in XPS possible to build high deviation in binding energy larger than 5 eV??

Hello. Thanks for your consideration to see my question. Recently, I conducted XPS anaylsis of g-CN that is prepared from thermal polycondensation of DCDA, so-called conventional bulk-g-CN,...

30 July 2024 9,824 2 View

Which statistical test should we use?

N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.

30 July 2024 7,233 4 View

How to build my own lab made four point probe set up?

Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...

30 July 2024 906 2 View

Can the limit of quantification (LOQ) of an analytical method fall outside its linear dynamic range, or must it always be within it?

Can an analytical method's limit of quantification (LOQ) be outside its linear dynamic range, or is it always required to be within it? Please provide a thorough explanation supported by verified...

29 July 2024 7,198 9 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Do you know best mines of western part of Afghanistan?

I want to know more about Mn deposits in west of Afghanistan.

07 August 2024 3,427 1 View

I have no added any resarch paper yet but showing three paper? how to delete it?

I have not addede any paper yet but it has selected 3 papers which are not mine in my account. i want to delete that information. please help me

30 July 2024 3,743 0 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

What topic or subject does Production Engineering need to address more?

Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?

27 July 2024 648 3 View

Can you recommend provider Intermediate laboratory test for hydrocarbon, polyethylene & polypropylene?

Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...

25 July 2024 8,108 0 View

Can we eliminate the stress singularity at the tip of the crack by manipulating the elastic constants?

The aim of the research here is to prevent the propagation of the crack in the fabricated elastic medium with useful applications.

25 July 2024 9,976 3 View

Pedro Barrios

thank you! your answer was really useful. with this I made a nice continuos and conformal meshing. thanks a lot.

By the way, I want to ask you about meshing statistics, ¿when is it a good quality mesh?.

Christos Andrea Christou

Found this useful

https://www.youtube.com/watch?v=R_DM2kRszYw