Where can I find detailed design guide for pulsating heat pipe?

More Ashutosh Gupta's questions See All

What is the step by step procedure for performing parallel processing in ansys fluent?

In my computational model of Pulsating heat pipe, I have very small time step (10-7) with 20 iterations each. So to reduce the computational time I am supposed to perform parallel processing in...

08 September 2016 7,369 0 View

How to define vacuum in ansys fluent?

In modelling of Pulsating heat Pipe in ansys fluent I am supposed to create vacuum to initiate the simulation. Any help....

07 August 2016 8,907 5 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

Some new emerging problems on application of RL for scheduling in IoT networks?

I have seen plenty of existing works on applied Reinforcement Learning (RL) policies for optimized scheduling in IoT networks including Q-learning, DQNs, and the newer ones including PPO for...

01 August 2024 8,754 2 View

Conjugation of PEG-Amine to an Amino Acid Using EDC?

I am attempting to conjugate PEG to an amino acid at the C-terminus, for the purposes of producing nanoparticles. I have been told that PEG modified with amine groups can be used for this purpose,...

31 July 2024 2,033 1 View

Where to find a gene list for CRISPRa/i library screening of regulatory factors that affect pathogenic Th17 differentiation in PBMC?

I want to perform a CRISPRa/i library screening for candidate regulatory factors that affect pathogenic Th17 differentiation in PBMC. But I am wondering how to define the size of gene library, so...

31 July 2024 2,150 0 View

Zoubair Boulahia

Use this forum cfd.online it can help you. Good luck.

Niti Kammuang-lue

"Closed loop pulsating heat pipes Part B: visualization and semi-empirical modeling"

Applied Thermal Engineering, Volume 23, Issue 16, November 2003, Pages 2021-2033

Sameer Khandekar, Piyanun Charoensawan, Manfred Groll, Pradit Terdtoon

Ashutosh Gupta

Thanks for sharing the book, vitalii