10 February 2020 3 5K Report

For example: date of authorization, date of cancellation, used active ingredient, DPI capsule type for capsule-based DPI inhalators, etc.? I can't find an official and up-to-date list of those on the market in the world, in Europe, in the USA, only in my country, Hungary, so far ...

More Edit Benke's questions See All
What equipment and how to easily determine the Peclet number (Pe) for dry powder inhalation systems?

In the articles I have read so far, I have found no exact values, only an explanation that if the Pe is 1, then we can see...

09 February 2020 403 3 View

Can I find the more siutable than SrucureHarvester sofware to analysing my microsatellite datas if the Strucure output larger than 75MBe ?

microsatellites; run lenght: 10.000; MCMC reps.: 10.000; Nr. of iteration: 20; Set a K from 1 to 25

06 January 2017 665 3 View

Similar questions and discussions
What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Necessary tube lenght to cool Natural gas in a dry-ice cooling bath?

I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...

27 February 2021 8,128 1 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

How to realize refractive index values of 1 to 1.1?

Hello researchers! While studying the literature on refractive index sensors, most of the articles simulate their devices with a refractive index ranging from 1 to 1.1, with small steps in...

17 February 2021 1,578 4 View

How to get better phase shift in C-V curves for ferroelectric devices?

I tried to sweep my ferroelectric devices from -2V to 2V and then from 2V to -2V and The two hysteresis peaks are off by several microFarads. Should i increase bias voltage? I am doing these...

16 February 2021 8,514 2 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close