What is the reason of collapse of water tank shown in the attached you tube?

https://www.youtube.com/watch?v=WLEkC_JbTsQ

03 April 2017 1,021 2 View

No title

02 March 2017 8,545 19 View

Why do BS8007 specify the allowable crack width of water retaining structure as 0.2mm for severe or very severe exposure?

Why 0.2 mm crack width?

02 March 2017 9,166 3 View

Which type of multiple-cell box girder is better, cells connected by top flanges or cells connected both by top and bottom flanges?

How we can design box girder bridge?

02 March 2017 9,977 3 View

What is the effect of rusting on steel reinforcement?

How does rust affect on the bonding between steel bars and concret?

02 March 2017 3,267 10 View

What is the difference between working stress approach and limit state approach?

02 March 2017 415 2 View

It is not necessary to design nominal reinforcement to piles. Is it true?

Can we use same code provisions of columns for piles?

02 March 2017 7,705 3 View

In carrying out compression test for concrete, should test cubes or test cylinders be adopted?

Relation between cubes and cylinder

02 March 2017 5,645 4 View

If concrete compression test fails, should Schmidt hammer test be adopted as an alternative test to prove the concrete strength?

Non destructive tests

02 March 2017 5,232 31 View

What is the meaning of P-delta analysis?

Some codes provisions refer to this type of analysis.

02 March 2017 8,549 5 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Is stone a sustainable material? Is it a sustainable approach to use natural stone waste in architecture?

I'm designing a zero-waste restaurant and considering using marble waste to make some tables and a bar countertop. My clients think it's not "sustainable enough" and I would like to have more...

01 March 2021 4,326 7 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Apart from Nanosilica and CNT's what are the other nanomaterials readily available to use in concrete mixture?

Nanotechnology in concrete materials

01 March 2021 3,379 3 View

Is anyone familiar with the cyclic compressive fatigue testing (BS EN 12697 - 25) ?

I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...

28 February 2021 2,004 3 View

Microstrip antenna design tutorial of HFSS 3D layout module ?

I have designed a 24 GHz rectangular antenna on HFSS 3D model and got desired results while desing the same antenna with same dimensions I am getting resonance frequency at 27 GHz I am...

28 February 2021 4,426 2 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

How relevant is Mini slump cone?

for all the rheology researchers, my question is, how relevant is a mini slump cone (smaller than a standard 50 cent rheometer). currently based on testing, the thickness of slumped material is...

26 February 2021 3,668 1 View