checking the Pulse duration is very important in order to calculate the power of the laser beam for this 1000 minutes?
Laser pulse duration is 5ns with rep rate is 20Hz.
Drear Ghulam Raza Mangi
thank
Great regard
Have you calculate this laser influences & peak power ??
How many naïve T cells we can get from a C57BL/6J mouse spleen and lymph nodes? or in other word, what percentage of the cells from spleen and lymph nodes are naïve T cells?
15 May 2023 1,478 3 View
Greetings Patton (1966) described the effects of surface roughness on the shear strength measurement and this formula was found (τ = σ tan (φ + i)). I tried to get a reference with all the details...
09 February 2023 608 0 View
How to calculate and design LCL filter for harmonic reduction in matlab simulink?
07 February 2023 3,131 3 View
Despite the improvement in oral dental health in several countries which can be achieved through the use of fluoride measures, caries incidence is still widespread and is a cause of concern in...
31 May 2021 2,738 22 View
I am reviewing a paper for ANSYS application in Shape Memory Alloys snice the access denied for Our country to the web site is there a chance or a possibility there is a Margene of error in the...
18 March 2021 3,673 3 View
I wonder, is there a possibility to use nano particles materials to eliminate covid 19 after it enters human cells, especially lungs? regards Raad Sh. Alnayli
31 March 2020 5,074 6 View
It is possible to measure the third nonlinear susceptibility in the continue laser Z scan set up and why if it is not ?
16 February 2020 9,079 8 View
In the z scan techniques to study the nonlinear properties of nonlinear materials ,which are determined to use cw-laser or pulsing laser,?is thick or natural of the sample?
13 August 2019 7,692 5 View
how we can perform the herbal extract antibacterial MIC?
01 January 2019 9,619 9 View
What would be a good conference/symposium/congress that would be suitable for the research of new methods where in-vitro experiments of Layer-by-Layer covering of bacteria is studied? If anyone...
12 December 2018 3,597 3 View
i am unable to interpret why its increases in start as shown in figure
11 August 2024 2,179 1 View
Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...
11 August 2024 8,141 3 View
I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.
09 August 2024 9,894 2 View
Hello everyone, I'm encountering an issue with my electrochemical impedance spectroscopy (EIS) measurements and would appreciate some insights. Experimental Setup: Electrodes: Gold interdigitated...
05 August 2024 3,783 2 View
I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...
05 August 2024 3,290 1 View
I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...
01 August 2024 9,227 1 View
Following curve related to Co0.6Mn0.4Fe2O4 Magnetic nanoparticles with extra phase a-Fe2O3. I will appreciate to help me to interpretation this spectroscopy, especially the blue line.
31 July 2024 9,140 2 View
Hello everyone, I am new to this characterization but watching videos on youtube I have already plotted a Nyquist plot (Z' and -Z'') and already fitted models on my material using Zsim. But now I...
29 July 2024 1,376 0 View
Your comments
28 July 2024 2,822 2 View
There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...
27 July 2024 7,168 2 View