What the effect of laser spot size on surface modification?

More Abdulhadi Kadhum's questions See All

Who is more accuracy to determine the grain size XRD or AFM?

Whose more accurate to determine the grain size XRD or AFM

01 February 2017 5,274 0 View

What the proper confienment to prepare Ni nanoparticles by laser ablation?

the type of confinement to prepare Ni nanoparticles by using laser ablation method

01 February 2017 9,205 0 View

What laser conditions for nickel ablation?

Preparation of nickel nano particles by laser , I want laser type , laser energy ,...etc

01 February 2017 3,440 0 View

How to determine thin film thickness by XRF?

I need to calculate the thickness of oxide film on steel plate by XRF technique

01 February 2017 8,030 0 View

What the baisic reference for thin film technology?

I need the main ref. of thin films

01 February 2017 4,759 0 View

How to determine the wear rate by optical method?

The experimental procedure for optical method to calculate the wear rate in metals and alloys

01 February 2017 4,978 3 View

How to determine the refractive index of liquid by laser?

please send me any information about refractive index of liquids by using laser

01 February 2017 2,356 0 View

How to determine the thickness of thin film by optical microscope?

Explain method to determine the thickness of thin film by optical microscope

01 February 2017 7,908 1 View

What the effect of thim film thickness on I - V characteristiv?

I-V properties influenced by thin film thickness

31 December 2016 3,445 2 View

What the definition of Miller indices of Eribium oxide?

From XRD pattern of Eribium oxide

11 December 2016 2,290 0 View

Using OBD technique i am trying to measure laser induced shockwaves velocity i found that at start velocity increases and then decay?

i am unable to interpret why its increases in start as shown in figure

11 August 2024 2,179 1 View

I have get this error when i calculated the geometrical optimization for prco3, it takes 12 hours until gives this message in the outputfile?

Fatal error in MPI_Allreduce: Other MPI error, error stack: MPI_Allreduce(1628)......: MPI_Allreduce(sbuf=000002459254A180, rbuf=000002459F86A140, count=4851, MPI_DOUBLE_COMPLEX, MPI_SUM,...

09 August 2024 7,615 1 View

Hello researchers Is this a random laser or just fluorescence?

I am using Rhodamine6G as gain medium and silver nanoparticles as scatterers on a microscope slide and laser input 532 nm comes from above.

09 August 2024 9,894 2 View

What is the prepared reference material that can be used in inductively coupled plasma optical emission spectrometry (ICP-OES) to measure REE and U ?

What is the prepared reference material that can be used in the ICPE-9820 Shimadzu Japan instrument, which employs inductively coupled plasma optical emission spectrometry (ICP-OES) to measure...

06 August 2024 1,896 1 View

Could dyes amplify the spectrum of light to a specific wavelength?

I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...

05 August 2024 3,290 1 View

How effective is the Citi Bloc standard basket in enhancing the accuracy and comparability of international construction cost assessments?

Citi BLOC Standard Basket Definitions: A standardized unit representing a fixed basket of construction materials, labor, and equipment costs priced in various cities. Purpose: To create a common...

04 August 2024 8,997 1 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Can I proceed with Response Surface Methodology (RSM) with only one factor for further optimization?

I went for Plackett Burman Design for selecting the optimization factors of growth conditions for pesticide degradation. I started with 7 parameters. But, after the experiments and analysis, only...

29 July 2024 5,015 1 View

I did hirshfeld surface analysis for molecule but did not find red spot and interaction surface in energy frame work, is it ok for research article ?

In hirshfeld surface calculation i did not find any red spot in hirshfeld surface, is it ok for research article to write?

28 July 2024 2,988 0 View

How should operational parameters be selected when developing a pore-free laser welding technology?

There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...

27 July 2024 7,168 2 View