What is the value of Maximum principal strain at failure for concrete 50 MPa?

Davoud Shahgholian-Ghahfarokhi @Davoud_Shahgholian-Ghahfarokhi

01 January 2018 0 5K Report

The maximum principal strain at failure is main parameter for concrete modeling in Ls Dyna software. I need to this parameter for concrete 50 MPa.

Badges
Science topic

More Davoud Shahgholian-Ghahfarokhi's questions See All

Is there any protocol for the histological evaluation of colon biopsies after ex-vivo culture?

I want to evaluate and compare human colon biopsies after 24h ex-vivo treatment with inflammatory and non-inflammatory cytokines. Apart from the H&E assessment, is there any protocol for the...

08 February 2024 5,357 3 View

How can I find the sequences of germline Transcript of IgG2c and IgA antibodies to evaluate class switch recombination?

To evaluate class switch recombination in B cells, I need to do QPCR on the Germline Transcription of IgA and IgG2c. But I can not find the sequence of these non-coding transcriptions. Also, When...

01 November 2023 1,366 0 View

Can we use mcf-7 and MDA-231 to induce breast cancer in balb/c mice that it is not nude (scid-deficience )?

There is just protocol to induce mammary line breast cancer in non-nud mouse that is 4t1

13 April 2016 781 2 View

Can we use mcf-7 and MDA-231 to induce breast cancer in balb/c mice that it is not nude (scid-deficience )?

There is just protocol to induce mammary line breast cancer in non-nud mouse that is 4t1

03 April 2016 6,292 2 View

What may be the reasons for failures of Tube toi Tube Sheet Joints in Boiler Drum ?

We have observed that tube to tube sheet joint leaked in our boiler and needs to overcome same by knowing the root cause.

08 August 2024 3,161 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

How to add viscosity into a hyperelastic material such as Mooney-Rivlin rubber in LS-DYNA?

Hi, I am working on a head FE model and want to try different material types on brain. I read some papers that use Mooney-Rivlin rubber model and wondering if i can add viscosity into it. Is it...

24 July 2024 5,908 0 View

Sample size for qualitative study?

I am working on scale development in behavioral finance by undertaking a mixed-method approach using the exploratory sequential design. The phenomenon has diverse meanings in existing literature...

20 July 2024 9,153 11 View

Zero pivot in Abaqus concrete 3D printing simulation using model change?

Recently I've been working on a simulation of concrete 3D printing, and has successfully simulated a layer-by-layer 3D printing process using model change. However, when I proceeded to try...

06 July 2024 2,130 0 View

Are there any people using biolegend anti- mouse CCR2-BV785?

Hi, I'm working on heart flow cytometry, and I use anti-mouse CCR2-BV785 (biolegend, cat150621) for staining, 20 minutes, 4 degree. But I couldn't see any CCR2+ cells. So I'm not sure if it's...

03 July 2024 3,969 4 View

What heavy aggregates are available for protective concrete in your country?

01 July 2024 1,625 3 View

Poured Earth Concrete ?

What are the benefits and advantages of concrete flooring when used in parking lot floors, and what are the technical requirements and general specifications that should be considered to ensure...

29 June 2024 2,171 5 View

Why did the simulated load-displacement curve of beam keep increasing and didn't decrease (ABAQUS)?

Dear colleagues, I'm currently modelling a simple 4-point bending test of a concrete beam in Abaqus. However, the load-displacement curve was ascending (without final point), which didn't match...

29 June 2024 6,192 2 View