Hello, I am working on a heat transfer research and I wanna use Eckert number but the cp value is for the fluid "water" or what?
Thanks
Thanks !
Look at this. Good luck.
http://www.thermopedia.com/content/714/
Really thank you sir!
Hello, I have a simple model (PV cell+ air channel) and I do not know how to let the sun rays hit the PV surface and then transfer the heat to the air..What I see is the sun rays hit the air...
08 September 2019 688 2 View
Hello, I need the equations that show the coefficient of the matrix that solves the velocity contours of the boundary layer over a flat plate. I have the explicit discretization equations but I...
05 June 2019 8,078 4 View
Hell, how can we write a UDF to include a heat flux value + convection coefficient for a wall in Fluent because we cannot define two named selections for 1 wall ? Danke!
05 June 2019 7,188 12 View
Hello, I want to simulate the half of the domain and define a symmetry wall because I do not want to consider it as the edge wall, I want to consider it the wall at the half of the domain..How ca...
04 May 2019 6,100 3 View
Hello, I want to know how to use ANSYS Chemkin to model the attached model in the attached paper. the videos on internet are so simple. Thanks
04 May 2019 4,064 2 View
Hello, we have done a simulation using ANSYS FLUENT, can we couple it with ANSYS simplorer? And if yes, how and what are the documents I can study? Danke!
03 April 2019 2,799 6 View
Hello, I have a wall which is affected by a heat flux and it is cooled by convection..How can we do this in FLUENT? Thanks
02 March 2019 6,112 4 View
Hello, we wanna write a thesis and we need the equations used for simulating the temperature distribution over a PV panel.. Where can we get these equations that ANSYS uses ? Thanks
31 December 2018 5,908 5 View
Hello, we have a CFD code written in MATLAB and we wanna save the calculations at a specific node to a text file like ANSYS FLUENT..Any suggestions please? We will be extremely grateful! Thank you!
31 December 2018 934 3 View
Hello, I have this UDF and it says that the airfoil changes the degree to +/- 8 through 1 sec, how is to work and how can we control the angle? /**********************************************/ /*...
09 October 2018 4,673 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,989 3 View
is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it
06 August 2024 947 1 View
I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?
04 August 2024 1,537 1 View
My screen printed electrode CV is given here. For Nerstean one electron reaction the delta E value should be close to 57 mV and ration of Ic/Ia should be close to 1. I did CV of my screen printed...
30 July 2024 4,671 3 View
Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...
29 July 2024 1,092 2 View
A computational study of heat flux on cylindrical surfaces using CNT hybrid nanofluids
28 July 2024 4,985 1 View
I would like to conduct artificial sunlight experiments to mimic heat capture and air warming in a greenhouse system. The main objective is to heat up the temperature inside the greenhouse, not...
28 July 2024 4,006 2 View
Hey researchers! I am currently doing a research about to what extent in which A has accelerated the inclusiveness of the payment system in my country. Down below are a few examples of the...
26 July 2024 5,654 3 View
Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...
25 July 2024 2,309 5 View