What is the relation between young's modulus and shear strength of the soil ?

More Dinesh Kr. Malviya's questions See All

Sensitivity analyze for crop evapotranspiration (ET0)?

Does anyone know how to perform a sensitivity analysis for crop evapotranspiration ( FAO Penman-Monteith equation) using daily meteorological data?

27 December 2020 9,552 3 View

How do I DERIVE equations for lumped elements (R, L, C) from S-parameters?

I have modeled the lumped element circuit for the 3D structure which has been simulated in HFSS. Now I need to derive the equations for the lumped elements keeping the S-parameters of the...

23 December 2020 172 3 View

No title

For academic writing.

17 December 2020 6,465 5 View

How to get nanocomposite of PEEK with Zirconia ?

Need a lengthy PEEK with Zirconia based nano composite of 180 mm length. Which method is possible? Tried injection molding no proper mix. Solvent casting process is also very costly. Kindly anyone...

13 December 2020 4,329 5 View

How to identify and quantify glauconite and illite/other mica present in same sample from XRD analysis?

In glauconite bearing sand stone sample other mica group minerals(illite, muscovite etc.) are also present. I want to quantify the amount of glauconite and othermica group minerals. How, I can...

10 December 2020 5,793 19 View

Choice of sampling time in discretization of control?

What I understand is while applying continuous control to a continuous-time system in MATLAB simulations, actually the control is being applied in discrete manner inherently due to the nature of...

28 November 2020 1,866 4 View

Simulation of sliding mode control for a maglev system?

I tried to simulate a maglev system with continuous time sliding mode but my simulation is showing error (there is a singularity at one of the integrators). I am attaching the modelling and...

16 November 2020 8,964 7 View

Can anyone suggest is there any way to compare the amount of chattering in 2 approaches of sliding mode control in quantitative way physically ?

Suppose 2 methods are shown to do sliding mode control of a given system. Please tell me if we can compare chattering in both by MATLAB or some other way

16 November 2020 3,251 3 View

On what basis two ceramics to be added in base metal to prepare hybrid metal matrix composites?

I am working on Mg-based metal matrix composites. I added two different types(A&B) with a suitable percentage(1%,2%,3% and 0.5%,1%,1.5%) of ceramics separately using DOE and tested. Now I want...

14 October 2020 2,984 9 View

Where i can get Ti based C94 catalyst ?

Ti based C94 catalyst is required for PBAT synthesis

12 September 2020 7,174 4 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

What are effects of steel jacketing on flexural strength?

Dear all, If steel jacketing is used to retrofit a reinforced-concrete (RC) column, can we use it to improve flexural strength? I understand that we leave gaps between the ends of the jacket and...

22 February 2021 1,906 5 View

Is there any kind of data available for connection properties like signal strength between UE and RAN?

Is there any kind of data available for connection strength between UE and RAN? I am looking for signal strength, the geographical coverage of RAN's in a given Tracking Area, Coverage Area over a...

16 February 2021 1,073 5 View

Can anyone direct me to an existing Validated Health Care Survey/Instrument?

Hello, I am working on a paper and looking for an existing Validated Health Care Survey/Instrument. I have been performing virtual ergonomic evaluations since the start of COVID and want to...

04 February 2021 4,756 2 View

Fracture energy of concrete at sub-zero temperatures?

Both tensile and compressive strengths of concrete increase with the decrease in temperature. With this in mind and considering that fracture energy is in direct correlation with the so-called...

18 January 2021 8,778 4 View

Why the fracture energy of concrete increases with the rise in temperature?

Given the degradation of mechanical properties in concrete under elevated temperature namely, tensile strength, modulus of elasticity, compressive strength, etc., what is the justification behind...

15 January 2021 3,651 4 View

What is interdependence theory in international relations?

I need a thesis on Independence theory in international relations, it's strengths and weakness with interstate examples

12 January 2021 4,334 2 View

In your opinion, what is the minimum thickness of the sheet in steel shear walls that will show the best efficiency due to earthquake force?

11 January 2021 2,417 2 View

What statistical analyses can I use for non-normal data overtly recorded with a 3 point scale and underlyingly recorded along a 0-100 scale?

I am struggling to understand what method of statistical analysis would work best for my data. I have a small sample of repeated measures data (15 participants in total) and I've asked them to...

09 January 2021 8,118 4 View

Dinesh Kr. Malviya

thank you Prof. Mohamed Beneldjouzi , but I am looking for relationship between shear strength and Young's modulus (E)

Plz share the reference, if it is okay

Kundan Raj Parajulee

This article might be helpful to you.

Article Predicting the geotechnical performance of Lisan Marl using ...