How is possible to design shear wall with openings in OpenSees? What are the ways? which one is more practical and faster?

Hooman Zolfaghari Nasab @Hooman-Zolfaghari-Nasab

09 June 2024 1 9K Report

shear wall with openings and without openings

Finite Element Modeling and Equivalent Frame Modeling are two approaches to design shear walls with openings in OpenSees. The more practical and faster method depends on the complexity of the structure and the required level of detail.

More Hooman Zolfaghari Nasab's questions See All

How to export DigSilent Plots with high quality?

Hi all; I've started using DigSilent these days. However, I'm wondering how can I export the results with high quality the same as MATLAB plots as I currently do. Thanks

19 December 2020 2,666 2 View

Exchanging data between GAMS and Excel !?

Dear researchers, I have the following questions: 1. I want to know how I can read a number of TABLES and PARAMETERS from excel? 2. How can I make GAMS show the zero values as "0" in the results?...

08 March 2020 4,416 5 View

Is it OK to use more than one statistical analysis software to analyze the data and report the results in the research paper?

I'm analyzing my data and since no statistical analysis software is perfect, I was wondering if it's possible to use more than one statistical analysis softwares to analyze the data and...

01 March 2020 593 8 View

Does anyone know aboat meal worm breeding and production??

Hello . I have been working on meal worm breeding for about a year, and I have a small farm . I encountered a problem recently. When a pupa is born and becomes a beetle, a large number of them...

15 February 2019 5,230 4 View

Available implementations for raster-to-raster registrations?

Dear Colleagues, i am a bit indecisive about choosing a convenient, though accurate implementation to fit two rasters, consisting of Canopy Height Models from different 3D data sources, across a...

04 September 2018 649 11 View

Inverter controller for F28335 control card?

Hello, I am looking for grid-connected PV inverter and battery inverter controllers to implement on TI F28335 control card. Typhoon already provides some examples (.out file) for the controllers,...

01 January 1970 6,151 7 View

Can anyone suggest the working on concentration of DAPI for fluorescence studies?

Concentration of DAPI for fluorescence studies

01 January 1970 6,152 3 View

A question for writting proposal?

hello, I would like to write a project for DFG. I would like to know that how much DFG support for projects and the duration of projects is limit or not? Also, Can I have your proposal draft?...

01 January 1970 1,609 1 View

Synergistic effect calculation?

Hello Everyone, I have a question regarding synergistic effect calculation. We did one experiment on degradation of phenol in leachate by means of natural attenuation. The factors that are effect...

01 January 1970 5,997 2 View

XRD Rietveld Refinement- Refining a series of patterns

May you know any methods/software/ or techniques capable of refining a series of similar XRD patterns? I am talking about Rietveld refinement.

01 January 1970 1,779 12 View

In your opinion, what is the minimum thickness of the sheet in steel shear walls that will show the best efficiency due to earthquake force?

11 January 2021 2,417 2 View

Search for article DOI: 10.1007/978-981-15-6463-5_57 ?

Have been looking for the following article: Review of Experimental Techniques for Evaluating Unsaturated Shear Strength of Soil. In book: Advances in Civil Engineering and Infrastructural...

04 January 2021 9,780 4 View

Why does bending stress(Sx) in ANSYS APDL direct below of point load FE 2D modelling simply supported point load higher than exact solution in value?

Why does normal bending stress/flexural stress value (Sx) just direct below a concentrated load of simply supported beam which is compression stress higher than the hand calculation Exact solution...

03 January 2021 8,462 3 View

Why does shear stress (Sxy) result in ANSYS APDL area element type solid 182 or 183 quadrilateral or triangle will be efferent in a cantilever beam?

Why does shear stress (Sxy) result in ANSYS APDL area element type solid 182 or 183 quadrilateral or triangle will be different in a cantilever beam with point load at fixed end or uniform load at...

31 December 2020 9,359 3 View

Does ANSYS consider the thickness of the shell181 element for the stress results?

Is the stress throughout the thickness of the shell element the same? I learned that transverse shear stresses are accounted for in SHELL181 but I also read that stresses in shells along the...

28 December 2020 4,515 4 View

Are there empirical correlations available that relate data from grain size distribution curve to the shear strength of soil?

Similar to the Hazen formula for estimating permeability from the gradation curve of soil, can we identify the angle of shearing resistance of silty sand and sandy silt type of soil?

03 December 2020 6,747 3 View

Qusetion solved and removed ,thanks you?

question solved and removed, thanks you

21 November 2020 6,178 2 View

How to approximate the unsaturated shear strength parameters of unsaturated soils using the conventional triaxial setup ?

Shear resistance of unsaturated soils

08 November 2020 4,510 4 View

Can we determine undrained residual strength parameters ? Can ring shear test be used ?

Do we have any laboratory tests to determine the undrained residual strength parameters ? We use reversal direct shear test or ring shear test to determine residual strength, but in general both...

25 October 2020 8,062 3 View

Why does my Abaqus FEA simulation run forever?

Hello! I have recently been trying to model friction between two blocks of different materials in Abaqus FEA. I have started with a very simple model with two cubes of different materials next to...

17 October 2020 1,268 18 View