In pulse tube cryocooler analysis, a quantity named cycle averaged pressure drop, cycle averaged mass flow comes into the picture. My doubt is it average means RMS average or simple average? Please specify with example.
hope that helps you.
http://www.google.com.ng/url?sa=t&rct=j&q=&esrc=s&source=web&cd=6&cad=rja&uact=8&ved=0CDcQFjAF&url=http%3A%2F%2Fwww.freestudy.co.uk%2Fthermodynamics%2Ft4201.pdf&ei=KA5cVOWlMtavacbWgvAE&usg=AFQjCNF75yy5JdpLzaZBemf9eMHLEe5Jmg&sig2=DJgty6aLLWXQjBVkUs2npg&bvm=bv.79184187,d.d2s
Currently I have prepared a circuit which gives me constant current source of 10 micro ampere. 2 Volt DC source and 200 k Ohm resistor in series. What if the output volt of DC power supply...
05 June 2016 7,242 4 View
Currently FVM is most popular method to solve fluid flow involving heat transfer problems and related physics. On the other hand, FEM is mostly suitable and popular for structural analysis.
06 July 2015 7,634 0 View
What is the meaning of numerical diffusion? How to reduce or avoid it?
04 May 2015 7,981 3 View
Currently I am using Gauss Siedel Iterative method to solve CFD equations. I am facing instability problem i.e. iterations keep on increasing without change in rms value for a given variable such...
11 December 2014 9,064 14 View
I normally read the terms viz. charged pressure and mean pressure while browsing cryocoolers research papers. I do not understand what is the actual difference between them? How do both differ...
08 September 2014 8,380 4 View
I am doing numerical modeling of pulse tube cryocooler (with oscillating pressure and temperature) with finite volume method. I have successfully implemented it with implicit scheme by use of...
07 August 2014 4,284 34 View
Currently I am doing numerical analysis of pulse tube cryocooler and dealing with various parameters keeping others constant. I am saving data of each set in my computer date wise. I want to know...
04 May 2014 8,339 1 View
I will be using a needle valve for my practical setup of project work. It is based on pulse tube cryocooler. I need to calculate the coefficient of discharge for needle valve for report purpose....
04 May 2014 7,367 7 View
I am currently doing numerical analysis of GM type Pulse Tube Cryocooler. Governing equations are a system of boundary value problems and one need to use shooting method to solve it (as per one...
02 March 2014 4,915 1 View
I am currently working on 1-D numerical simulation of pulse tube refrigerator. The governing equations are given in attachment. I have plotted results showing mass flow rate over the cycle (mass...
02 March 2014 1,092 0 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,989 3 View
is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it
06 August 2024 947 1 View
I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?
04 August 2024 1,537 1 View
My screen printed electrode CV is given here. For Nerstean one electron reaction the delta E value should be close to 57 mV and ration of Ic/Ia should be close to 1. I did CV of my screen printed...
30 July 2024 4,671 3 View
What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?
29 July 2024 7,714 4 View
In some data sources it has been grouped in Q1 and some shows it is Q2.
29 July 2024 4,227 2 View
A computational study of heat flux on cylindrical surfaces using CNT hybrid nanofluids
28 July 2024 4,985 1 View
Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...
28 July 2024 5,771 2 View