If we increase or decrease the ductility of 1060 grade aluminum tube then then what is the effect on the corrosion property.
It depends on what method you use to increase or decrease the ductility of 1060 grade aluminum tube。
I think you need to focus on one type of corrosion to be accurate on the relation between ductility & corrosion.
And I think you are talking about stress corrosion here and not all the types of corrosion since you mentioned ductility.
Please find the attached file, it is one good work done on the same subject you proposed.
Dear Sir Chen Ding
Thank you for replying me.
Below I given some picture Sir,
This is Refrigerant aluminum tube. Pitting corrosion occur in the bend position.
we know that bend property depends on ductility of a materials. But maximum pitting corrosion occur in the bend position.
So have any relation pitting corrosion and ductility?
Dear Sir Abdulaziz Albannai ,
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
How to use ERP System in Global University ?
27 July 2024 8,229 0 View
here's a concise guide for preparing your CSV dataset in Excel to identify flood-triggering factors using an ANN: Clean and Format:Address missing values (fill with mean/median or remove if...
21 June 2024 7,941 0 View
how do integrate ECG, PCG, and clinical data to apply early fusion multimodal?
10 June 2024 3,289 1 View
I have performed the Molecular Docking using ADFR suite, I have obtained the files in _out.pdbqt format for ligand docked poses, upon inspection, both visually and reading the pdbqt files of...
08 June 2024 8,130 2 View
Dear Respected Scholars, I am working on detection of microplastic in prawn. Although, all the other parameters assessed smoothly but I have encounterd a problem during isolation of microplastics...
05 June 2024 2,469 0 View
In basin delineation and hydrological modeling, selecting the exact value in Flow Accumulation to identify streams is a critical step. The Flow Accumulation tool calculates the accumulated flow as...
30 May 2024 6,107 1 View
Are multi-level models appropriate for binary outcome variables for DHS datasets? If yes, what is the process?
30 May 2024 2,035 2 View
For my project, I need to extract RNA from muscle tissue of EEL. I am trying but the yield is low and Purity not good. The 260:230 ratio is always below 1.50 and 260:280 ratio ranges 1.6-1.86 and...
15 May 2024 3,024 2 View
For the design of three phase inverter for three phase motor drive, which is better using low DC voltage (12 V or 24 V DC) for the inverter stage then step it up using three phase transformer, or...
08 May 2024 3,491 3 View
In general, when performing a Tafel analysis for corrosion resistance measurements, a line voltage scan is performed from say -250 to +250 mV vs. OCV at low scan speed around 0.125 mV/s. However,...
25 July 2024 7,982 3 View
I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...
22 July 2024 3,490 2 View
Would anyone be interested in collaborating on corrosion?
07 July 2024 4,726 2 View
It is required to make a precursor gel for a SAPO-11 Zeolite, the compounds are the following: * As a source of Al: Aluminum Isopropoxide (98%) Formula: C9 H21 O3 Al PM: 204.24 g/mol Density:...
01 July 2024 617 3 View
I am doing orthogonal cutting of aluminum. My forces are changing according to mass scaling. How to decide the scaling factor?
01 July 2024 3,749 0 View
we need surface area, corrosion current, equivalent weight and density of the metal involved for corrosion rate calculation in mm/year (lets say). For dissimilar metal welds, how can we measure...
30 June 2024 5,943 2 View
I am working with a polysaccharide grafted on chitosan and my corrosive medium is 3.5 wt% NaCl. My surface is carbon steel. I am struggling to obtain a proper trend for my corrosion results. I am...
29 June 2024 5,592 1 View
In nanocrystalline metals, the size of their crystalline grains affects how strong, ductile, and hard they are. Smaller grains often mean stronger metals but can reduce ductility. Controlling...
28 June 2024 6,925 0 View
I am doing 2D orthogonal cutting simulation in ABAQUS for aluminum. Reducing mesh size up to 0.08 mm reduces the error to 3% but further reduction leads to increase in error from 3 to 39%. Why I...
23 June 2024 9,080 0 View
Corrosion studies by electrochemical measurement.
19 June 2024 5,274 3 View