What is the difference between EH and HE mode of an optical step index fiber ?

16 June 2017 1 8K Report

There are basically two types of hybrid modes in a step-index fiber, denoted as EH and HE. In both cases all the six field components (three E-field components and three H-field components) are present. Please let me know the difference between these two hybrid modes. Are there any dominating components in it (as quasi-TE and TM modes in the rectangular waveguide) or anything else?

Nabarun Saha

thank you Florian, this is really helpful.

Badges
Science topic

More Nabarun Saha's questions See All

Is this 6GHz wifi antenna create complexity at the time of febrication?

I have design a 6GHz antenna for wifi.The feed line width is 2mm and there are 2 parasitic elements beside this feed line with 1 mm gap.Is there any problem at the time of febrication?

04 February 2021 9,241 3 View

How can you make a PEDOT:PSS film using the doctor blade technique?

I have been trying to make an even PEDOT: PSS (PH1000) film with the doctor blade technique (tape casting) with varying results. I have been using a silicon substrate that's treated with piranha...

01 February 2021 8,506 5 View

How robust are open source soil moisture sensors connected to an arduino board for field monitoring?

Seeking recent experiences in the development and deployment of low-cost soil moisture sensors (ideally under $50/sensor) connected to arduino-based dataloggers. What is the longetivity of the...

19 January 2021 6,256 2 View

How to separate a mixture of organic acids by GC?

I would like to develop a method for analysis of many organic acids in the same time. how to separate the chromatographic peaks of each one?

20 December 2020 8,399 3 View

Should I keep the missing values > 50%?

I have a data set of 771 sample size. But some of the variables (laboratory findings like ALT, AST, creatinie level) have more than 50% missing values. Should I drop those? But I think those...

13 December 2020 4,847 3 View

How to Strip off HSQ( Fox 16) after etching?

We are finding a hard time to strip of residual HSQ ( Fox 16) after using it as a mask in etching? We are coating 600 nm thick HSQ and writing with 3000 microC/cm^2 dose at 1 nA current. We are...

08 December 2020 5,452 2 View

Why the oral cancer cell line from metastatic tongue origin is showing less aggressive property?

I am working with oral cancer cell line SCC090 (ATCC). As per ATCC data sheet it is originated from metastatic tongue. It's primary site is not mentioned. Due to the origination from metastatic...

08 December 2020 5,674 3 View

In case of larger sample size (more than 700 sample) can I do t-test though the data is not normally distributed?

My sample size is more than 750 but sk test is showing non-normal distribution. The variables have several outliers but I shouldn't remove those. In that case what should I do? t-test or other...

06 December 2020 1,285 19 View

Why the western blot of HIF1alpha of the whole cell lysate shows intense band under normoxia without any induction of hypoxia?

I am working with oral cancer cell lines and trying to find the expressional changes of HIF1alpha under different experimental treatment. I am getting intense band of HIF1alpha in the western blot...

29 November 2020 5,707 3 View

Can someone help me with a code for R software for principal component analysis and even tell me how to arrange the dataset?

I am having a biparental mapping population of rice with dataset of various morphological and post harvest parameters from F6 and F7 and 6 checks in augmented block design.

17 November 2020 6,272 4 View

Is there a way to use waveguide ports for circular antenna design in CST?

Hi, whenever i use circular array i get this error "Waveguide ports must be aligned with Cartesian coordinate planes for the transient solver" Does anyone use circular array with waveguide ports?...

09 February 2021 3,609 8 View

Where is the active point of VCSEL?

I am now working on the coupling between vertical-cavity surface-emission laser(VCSEL) and waveguide. However, the window design for laser emission is larger than the waist of Gaussian beam...

27 January 2021 8,318 1 View

How exactly modes are coupled into asymmetric directional coupler?

Currently I am reading one research paper regarding silicon based two and four mode division multiplexing for optical data transmission in 2 micrometer waveband. While reading I stuck at one...

21 January 2021 5,864 4 View

What is corrct way to define ports when simulating FSS and surface waves in CST?

I need to simulate a mushroom FSS and I'm struggling with the ports. What's the correct way to define them? Should I construct a proper SMA connectors, or is it enough to put a waveguide ports...

19 January 2021 6,590 4 View

How to make sure each cavity modes with same E-field distribution in COMSOL simulation?

In COMSOL Application Library, there is case about waveguide adapter. But there are some questions: 1) In boundary mode analysis, it just set to find only 1 mode and the S-parameter is...

12 January 2021 9,383 2 View

Is it possible to introduce a 2D axis-symmetric model in COMSOL Multiphysics to solve electromagnetic waves?

Hello dear researchers. I want to solve a cylindrical waveguide, lick an ordinary standard optical fiber. I am familiar enough with the 2D-axis-symmetric model, but as I knew from the equations...

11 January 2021 6,663 6 View

Can I bend a grounded coplanar waveguide (GCPW)?

The straight line shows great results but modelling just one bend in CST gives very high reflection. Could it be a tool error or are GCPWs supposed to be straight?

11 January 2021 1,606 4 View

How to calculate width and length of the tapered microstrip line feed of a SIW leaky wave antenna?

With reference to substrate integrated waveguide -leaky wave antenna

26 December 2020 3,982 2 View

How to remove radiations in silicon substrate in the simulation?

I designed a plasmonic slot waveguide using gold on top of the 2 micron oxide layer and below the oxide layer, I used silicon as substrate. the idea is to optimize the waveguide dimensions (slot...

01 November 2020 4,400 3 View

How can we estimate the maximum power that an optical waveguide can handle?

Sorry for the naivety of my question. I am looking forward to estimating the maximum power capacity of an optical waveguide, typically, Silicon (Si) or Silicon Nitride (SiN) waveguide. Is there...

19 October 2020 4,915 5 View