What is the correct method to calculate lambda in the allele frequency model (Structure software)?

Olga De Castro @Olga_De_Castro

03 March 2018 0 5K Report

I have read the manual, but it is very vague about the modality to claculate this value.

Best regards, Olga

Badges
Science topic

Similar topics
Correction

More Olga De Castro's questions See All

Network software: example of a matrix for external rooting?

I am not able to analyse my matrix with outgroup using Network (input: DNA sequences). I tried a lot of versions. Have you an example matrix that I can see?

31 December 2013 8,320 3 View

What is the best method to read ssDNA, dsDNA and/or RNA? Is it fluorometer or spectrophotometer?

09 October 2013 3,773 7 View

Can anyone suggest articles about cpDNA inheritance in ferns?

My goal is to know if cpDNA of ferns is maternal or paternal or biparentally inherited. Thanks.

07 August 2013 7,789 5 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How Can I clain a removal of a co-author?

I would like to make a correction in a co-author in your paper which is wrong. This name is also in other papers of Kenton Ko. Zey Ko is not a Co-author . The correct name is Zdenka...

24 February 2021 3,476 4 View

How does the injection volume impact LLOQ and ULOQ in regression analysis (LC-MSMS)?

Hello, I have run into an issue that has sparkled a debate at work: is the LLOQ/ULOQ impacted by injection volume under the following circumstances: 1) Same dilution factor of all samples 2)...

23 February 2021 9,159 3 View

Difficulty in debugging code to correct error - TypeError: '<' not supported ?

I am trying with a Unet code ontained from net ...in tensorflow. When trying to predict the segmentation result with the trained and saved model with metric " iou" using "CustomObjectScope"...

22 February 2021 5,254 1 View

How to perform Haldane correction on SPSS?

I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...

21 February 2021 2,882 1 View

absorption= 1-mag(S(FP1:1,FP1:1)S(FP1:1,FP1:1))-mag(S(FP2:1,FP1:1)S(FP2:1,FP1:1)) is it correct for absorption ?

hi everyone I am simulating a unit cell structure in HFSS using Flouquet port having two modes for absorption I have used this formula:- absorption=...

17 February 2021 9,178 2 View

Unable to detect a truncated protein variant, but I can observe a truncated cDNA from Sanger?

Hi, so basically... I am trying to mimic a clinically observed condition wherein a frame-shift mutation happens only at one allele of the patients, giving rise to a truncated variant which evades...

17 February 2021 1,130 6 View

How can I calculate the magnetic force applied from a magnet (no electrism)?

I would like to calculate the magnetic force on a Fe304 particle which is into a liquid solution . The magnet is above the solution , and there is no electricity. I found this formula : F = (V...

13 February 2021 4,770 3 View

What is the best way to do symmetry in ANSYS Fluent for flow between two concentric cylinders ?

I am working on Taylor Couette flow between concentric cylinders and the results are correct for the full case. however, I wanted to do symmetry case to improve the mesh. I have tried periodic...

11 February 2021 2,193 6 View