What is the best scale up approach for spray rate in wurster process?

06 June 2016 0 8K Report

Whether spray rate in wurster process is proportional to the base plate or wurster column cross sectional area.

Badges
Science topic

More Srimanta Sarkar's questions See All

What is the most suitable approach for the scale up of atomization pressure in wurster coating?

In wurster coating process atomization air pressure plays an important role on coat quality. In the most cases, facility to measure droplet sizes is not available. In such cases, what...

10 November 2016 5,988 1 View

How to perform non-geomatric scale up for blending/dry mixing unit operation?

Most of available scale-up rules for dry powder mixing/ blending operation are applicable for geometrically similar equipments. Considering, equipments unavailability, sometime a blender with...

03 April 2016 3,601 3 View

Can any one please explain the term 'Forced Bioequivalence' associated with larger larger sample size due to high power consideration?

The sample size for the BE is directly poportional with power. However, the proposed/accepted power ingeneral is 80-90%. Consideration of power more than 90 % may end up the issue of ' 'Forced...

02 March 2016 7,933 2 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

Technology developments may it for whatever reasons developed eventually its benefits are multi-Disciplinatary?

Your comments

28 July 2024 2,822 2 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

New and trending areas in the field of production technology using microorganisms?

Novel areas especially

24 July 2024 8,416 0 View

How do you get pure primary macrophage cell culture?

I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...

23 July 2024 4,074 2 View

What are the strategies to Enhance IgG-Producing Plasma Cells in mice for Monoclonal Antibody Development?

I have immunized BalB/C mice with a protein using the intradermal (ID) method with Complete Freund's Adjuvant (CFA) and Incomplete Freund's Adjuvant (IFA), following a 14-day interval and three...

22 July 2024 9,160 2 View

I'm conducting a study on Research Commercialization in Pakistani HEIs and would appreciate your participation in a brief survey?

Dear Participants- Faculty and Researchers from Pakistani Higher Education Institutions, Thank you for participating in research study that aims to 'Analyze Individual and Institutional Factors...

18 July 2024 7,024 1 View