after production of Ti-0.2 Pd ingot by VAR (Vacuum Arc Remelting) process, ingot should be roll in high temperature to gain strength. what is best temperature limit for initial rough working and second hot working (rolling or forging)?
Is a person with a history nodular gastritis, which has been through nodular regression (according to endoscopy) because of sucessful H.pylori treatment, has the same prognosis as a person with no...
20 May 2024 4,192 0 View
For a ship panel, I want to consider the initial deviation (thin-horse mode) to have a better analysis. How can I apply initial deviation from Rigo method in Abaqus?
19 May 2024 1,358 1 View
The question inquires about the potential use of the sol-gel technique for producing fiber preforms (rods) and whether its application is limited solely to volume optics. The sol-gel technique...
15 May 2024 9,211 0 View
One of the most important analytical tools often used by management executives for decision making is decision tree analysis. The most well-known approach to solve decision tree problems is the...
08 May 2024 6,619 4 View
I want to know how peak and rms current of diodes and capacitors are calculated in terms of output current? if you know good reference with details, please share here or tell me.
04 May 2024 6,277 1 View
The question is about the safety mechanisms in place within a car battery pack to manage and reduce pressure after a cell explosion. This is a critical aspect of battery technology, particularly...
18 April 2024 3,376 1 View
what are more desirable journals for Russian researchers in structural engineering field to submit their papers? thank you.
13 April 2024 5,004 2 View
Hi, What is this organism? I found it in Quaternary sediments!
25 March 2024 8,298 7 View
Guidance, navigation, and control systems are used in many vehicles to achieve precision, reliability, stability, mission path planning, and ... . what are the primary objectives of GNC systems...
24 March 2024 5,946 3 View
Hello, Which are some AI tools that researchers can use in writing scientific paper?
23 February 2024 1,792 4 View
Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...
11 August 2024 8,141 3 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
Hello What should be done to separate and identify organic acids in HPC when their RetTime is the same?Like oxalic acid with Propanoic Acid.or acids that have a very close RetTime.
07 August 2024 8,782 3 View
I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...
06 August 2024 1,367 3 View
During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...
06 August 2024 726 3 View
How do you tie-break and rank these two in their strength?
03 August 2024 4,471 1 View
Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...
03 August 2024 2,546 2 View
A typical reforming section in a large-scale Haber-Bosch process (Figure 1) comprises two reactors. A mixture of methane (CH4) and steam (H2O) is fed into a primary reformer to produce syngas via...
01 August 2024 7,051 5 View
Hi everyone, I'd like to better separate two close peaks coming from a bioconversion sample, I'm currently using a C18 KromaPhase 4,6mm Ø.I. SCHARLAU, particle size (µm): 10, pore size (Å): 100,...
30 July 2024 435 3 View
Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...
28 July 2024 6,553 1 View