What is suitable MOC and coating for plug flow reactor?

More Kiran Subramani's questions See All

How to fix W/V % for Nano fluids in heat transfer application?

Is there any specific range of W/V% for nano particles (like ZnO, TiO2 ,Fe2O3 ) used to increase the heat transfer rate ? Interfere both in economical viability and heat transfer rate Note:...

01 February 2018 9,843 3 View

How to increase the solubility of CO2 in water at high temperature?

As the solubility of gas in liquid decrease with increase in temperature, is there any possibilities to increase the CO2 solubility in the water around 50-80 C?

08 September 2017 3,274 4 View

How to calculate the initial head space pressure required to keep water in liquid state?

I have a 750 ml reactor and working volume is 300 ml. my working temperature is 350 C. By using ideal gas law i found at the pressure to be around 2 bar. But I need final pressure build up @ 350...

06 July 2017 5,943 3 View

How to design simple batch reactor of 1kg biomass for hydrothermal liquefaction ?

say me what type of MOC , specification and whether there should be any provisions for water circulation?

06 July 2016 9,542 2 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Research Methodology - Impact of Corporate Reputation on Stakeholders Behaviors?

Please can anyone support with the survey questions based on RQ measures and propose how to do it in FMCG industry and include as well the role of brand equity Thanks

06 August 2024 949 0 View

Anyone having idea about VN primer for miRNA primer design ?

How to design VN primer to attach with universal reverse primer

05 August 2024 2,116 3 View

Should I remove an item from a scale to raise Cronbach's alpha and McDonald's omega or is it better to leave it if they are both over .7 already?

Hello! I have this scale which had 10 items initially. I had to remove items 8 and 10 because they correlated negatively with the scale, and then I removed item 9 because Cronbach's alpha and...

01 August 2024 4,606 7 View

Is it possible to improve the reforming section of the Haber-Bosch process without using air separation units?

A typical reforming section in a large-scale Haber-Bosch process (Figure 1) comprises two reactors. A mixture of methane (CH4) and steam (H2O) is fed into a primary reformer to produce syngas via...

01 August 2024 7,051 5 View