I induced diabetes with STZ (40 mg/kg) after 4 weeks of high fat diet in Wistar rats. The rats are showing inconsistent blood glucose level. Why?

I induced diabetes with STZ (40 mg/kg) after 4 weeks of high fat diet in Wistar rats. After 72 hours, i checked the FBG of all the rats and majority of the rats had FBG above 350 mg/dl. After a...

24 September 2020 5,975 24 View

How is health affected by environmental hazard and toxins?

correlates of health, environmental hazard and toxins.

08 February 2019 475 8 View

How can the efficiency of sustainable energy be defined?

energy crises in the face human demand.

05 February 2019 6,304 7 View

Will recent innovation in driveless can make traffic light obsolete?

Someday cars might talk to each other to coordinate traffic patterns. Malikopoulos and collaborators from Boston University recently developed a solution to control and minimize energy consumption...

18 January 2019 1,182 7 View

Does inequality undermined economic performance in Africa?

There is no reason to believe that inclusiveness affects the sustainability of growth patterns only in developing countries, though the specific dynamics depend on a number of factors. For...

04 January 2019 4,924 4 View

Can GMM covariance serve the same purpose as Gaussaians Mixture Model Variance?

A Gaussian mixture model is a probabilistic model that assumes all the data points are generated from a mixture of a finite number of Gaussian distributions with unknown parameters. One can think...

20 November 2018 3,851 2 View

Where can I find the chromatographic method for the fragmentation of a Novel MOFs or Metal complex using GC-MS or LC-MS?

A novel Cu-MOFs was synthesized and characterized by CHN, FT-IR, TGA, HSM, UV-VIS, SEM and X-ray crystallography.The X-ray crystallography revealed that the copper ion coordinate to the ligand...

03 August 2017 4,779 3 View

Can anyone help with information on how i can attach 30 guage thermocouple on 21.34mm 316L stainless steel tube?

12 June 2016 2,772 4 View

What are the available techniques of removing cladding materials from metal sheet' surfaces?

Apart from machining technique, is there any other method through which cladding material can be removed from the surface of metal sheets?

26 November 2015 2,440 3 View

How do I solve Abaqus errors:"Zero or negative mass in element", "Excessive distortion of element number"& "Abaqus time increment has become negative?

I am trying to simulate a FSSW process but the above/below errors keep on emerging. I have applied adaptive ALE to try and eliminate the issues but the errors remained after submitting the job. I...

02 November 2015 9,138 4 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View