What is important friction coefficient, wear rate and hardness measurements in transparant conducting oxide (TCO) layer?

09 September 2017 1 3K Report

nanostructure

I think it is unimportant to measure the friction of this layer because it is not exposed to circumstances that requires it

Badges
Science topic

More Amr Ali's questions See All

What is the effect of applied frequency on optical properties and grain size? please, suggest any article

(transmittamce, energy band gap, refractive index, extinction cofficient, nanostructure and titanium dioxide

02 March 2017 6,113 0 View

What's the reason to rise refractive index values of titanium dioxide ? please, attached reference?

refractive index values of titanium dioxide ?

01 February 2017 1,567 0 View

What's the reason to reach energy band gap values of titanium dioxide to 4 eV ? please, attached reference?

energy band gap of nano thin film titanium dioxide reach to 4 eV

31 December 2016 4,424 4 View

How hardness values and friction coefficient for titanium dioxide as anti reflective for solar cell ? please mention reference?

values of hardness and friction coefficient for titanium dioxide user as application solar cell "user as anti reflective"

01 February 2016 940 0 View

What is the maximum thickness value reached of thin layer anti-reflective used in the solar panel system and the reasons for use on these cells ?

Value that can be up to them if you use a layer in the way pressing powders in the process of synthesis

31 December 2014 2,885 1 View

I need JCPDS file of LSFCO nanomaterial. Can anyone provide me?

Require for Rietveld refinement in XRD.

08 August 2024 3,081 2 View

Can formaldehyd-fixed gelatin be melt?

I am puzzled about the properties of gelatin, when used for tissue-embedding. Hard gelatin can be melt again by temperatures about 40°C. Formalin-fixed gelatin is like crosslinked protein and...

07 August 2024 1,686 1 View

Polymer wear calculation?

What is the method for analytically calculating the wear and service life of polymer-polymer sliding pairs?

04 August 2024 1,078 1 View

Why am I getting "shark finn"-like signal?

My collegue and I are having hard time to understand what is happening. Basically we have a tapping device that work with Arduino and a pneumatic pump. The pump allows the tapping of two...

04 August 2024 4,662 1 View

In SEM, if a latent variable consists of three observed variables, and each observed variable has four items, what should I do?

Suppose I am studying the construct of "Academic Motivation" (latent variable) in students, which is measured through three observed variables: "Intrinsic Motivation," "Extrinsic Motivation," and...

31 July 2024 3,913 6 View

Where to start the Analytical model for Dry sliding wear of metal surface ?

I am doing research on wear mechanism of the additive manufactured metal parts under dry condition. Please share the reference to start the analytical modelling of the wear prediction.

29 July 2024 6,115 0 View

Mechanochemistry: ball to powder mass or ball to powder volume?

I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...

23 July 2024 9,938 1 View

Correct statistical approach for a hermit crab shell exchange experiment?

Hello, I'm planning a shell exchanging experiment with two marine, hermit crab species inside of a tank. I only have one tank available for this experiment. I plan on running 30-40 shell...

20 July 2024 5,676 3 View

Can some indicate a technique - or approach - to measure the thickness of a 20µm film and thickness with water uptake?

Hi, I need to measure the real-time (or temporal intervals) thickness variation of a transparent material from dry to wet/humid conditions, however, I cannot use the following techniques: -...

08 July 2024 4,799 4 View

How can we build brand trust and transparency in a world of fake news and misinformation?

The rise of ethical consumerism

06 July 2024 1,277 0 View