Sheet steel laser cutting?

If you have a laser cutting machine that can cut a steel sheet up to 10 mm thick, is it possible to cut a 20 mm steel sheet in two consecutive passes? If the answer is yes or no, why?

09 October 2019 9,277 3 View

Lubrication regimen in pin on disk test?

I know that a way to establish the lubrication regime in a pin on disk test is by measure the resistance between the pin and the disc. Some papers say that if the resistance is of 2 ohm, the...

05 June 2019 7,779 3 View

How to create a mechanical engineering graphical abstract ?

Hi People. Here in RG there is a similar question but for works in biology. Some of you know if is there any software available to design mechanical engineering graphical abstracts ? Something...

31 December 2018 3,415 2 View

Warm forging of SAE 1045 steel?

Hi People. I need to know the temperture range for making warm forging of SAE 1045 steel.

31 December 2018 4,546 0 View

Hot forging dies made by SAE H13 tool steel?

Please. I need to know what level of hardness provide a equilibrated behaviour between wear resistance and toughness. Also, if a ionic nitriding treatment reduce the friction factor between the...

10 November 2018 6,466 1 View

Redes neuronales artificiales?

09 October 2018 8,748 0 View

Turning of low carbon steel?

People. I need your colaboration. What value of hardness do you think is the minimal to not worsen the maquinability level of the steel? I work with steel of 0,1% C. I some of you have a paper, is...

08 September 2018 9,234 3 View

How do I assess ignition risk during magnesium turning?

Some people say that the risk is bigger when the chip particles size are 500 micrometers or minus? What is the reason of this size?

07 August 2018 7,570 0 View

Recrystallization temperature of one steel?

Please. I need information about the recrystallization temperature of SAE 1010 steel, and also the temperature range for warm forging.

05 June 2018 5,685 3 View

Testing methodology of surgical drills used in bone applications?

Hi People. I need your help in relation to obtain technical information about testing methodology of surgical drills used in bone applications. This information may be standards, papers, and so...

02 March 2018 2,232 6 View

What are the most relevant MSc proposal topics for Petroleum Production Engineering at the moment?

I am a Petroleum Production Engg MSc student at Robert Gordon University in Aberdeen and I am in the process of selecting a topic for my MSc Engineering Investigation proposal. I would very much...

01 March 2021 7,396 4 View

RIA. How to measure?

When you use RIA, with a control the unknown sample with antibodies, you bare in mind the binding sites of the antibodies. However you still need to measure labelled antigen (radioactive) and not...

28 February 2021 2,133 3 View

How to Eliminate cosine error and abbe error in LASER measurement system(for example Rhenishaw XL80)?

I like to do project in laser measurement system. My objective is to eliminate or reduce the cosine error, abbe error in Laser measurement system. I have Rhenishaw XL80 system. Please tell the...

28 February 2021 4,890 3 View

How to measure angle between laser travel path and machine axis in Laser Measurement system?

25 February 2021 1,987 3 View

How to model Supercritical water gasification (SCWG) process in Homer software?

Hi everyone How to model Supercritical water gasification (SCWG) process in Homer software?

25 February 2021 4,075 1 View

How we can measure Kemp % in wool without using of benzene?

Would you please let me to know about the methods for measurement of medullation and Kemp % on animal? My problem is that the wool sampling and sending to laboratory is not possible. So I would...

21 February 2021 7,260 4 View

Could the "incoming radiation (net radiation)" values be negative?

Could the "incoming solar radiation" values be negative? What is the difference between "global solar radiation" and "incoming solar radiation"? Which one might be measured negative values?

21 February 2021 7,726 9 View

Can I follow Researchers from Teaching and testing areas?

I want Researchers from Educational Measurement and Evaluation, relating to teaching, learning , academic performance and test validation

18 February 2021 4,757 13 View

Is secondary metabolite production more at vegetative growth stage or during reproductive stage?

Hi, I am working on the effect of heavy metals on a medicinal plant by pot experimentation. Analyzing the effect of heavy metals on secondary metabolites is one of the parameters. I will be...

11 February 2021 6,683 6 View

How to determine measurement uncertainty of a mass balance?

Hi everyone, I work at a factory plant where they use a mass balance. The problem is that there is an huge difference between the input and output of one element. There are several people working...

10 February 2021 5,764 3 View