How can I selectively dry etch Ti on a polymer substrate?

24 February 2021 5,378 1 View

How to identify when a gaussian program is about terminate normally?

Dear all, I am trying to optimize a bimetallic complex using # opt=tight b3lyp/lanl2dz scf=qc geom=connectivity. The program is running for around 5 days but the size of the .chk remains same...

05 February 2021 8,721 3 View

How do you create a 0.5M EDTA disodium salt solution at pH=7.4?

I have been trying to make a 0.5M EDTA solution by dissolving EDTA disodium salt dihydrate in 500mL of purified water and adjusting the pH to ~8.0 so that the salt dissolves. To aid in the...

12 October 2020 3,242 2 View

How can I increase the length of DNA fragments recovered from QIAamp DNA Micro Kit?

Hi everyone. I'm performing DNA extractions for pools of ~10 individual Daphnia magna (water fleas) using the Qiagen QIAamp DNA Micro Kit. I use a pestle to homogenise the Daphnia before entering...

07 September 2020 9,956 1 View

Where could I find3D resistivity/conductivity (ERT) opensource data?

Hi, I would like to know whether is there any open source 3D inversion resistivity/conductivity geophysical data (ERT) available. If yes, how to access it?

06 August 2020 8,209 3 View

Is it normal to get different results when you try to simulate a paper your are basing your research on?

I am simulating AODV and AOMDV in NS 2 to compare their performance in terms of Packet Delivery Ratio (PDR), Throughput, Delay and energy consumption, in order to propose a better algorithm. The...

18 July 2020 9,755 9 View

How can I assess a method that returns high-expressed genes?

Hello, I working with a method that finds high-expressed genes in a single-cell experiment. How can I assess such method? I know I can compare it with the ones in literature (t-test, regression),...

22 February 2020 3,023 2 View

How should I hydroxylate tungsten powder for organosilane grafting?

I am having trouble depositing MPTMS/APTES onto tungsten and I am concerned there are not enough hydroxyl groups on the powder surface. So far I have been exposing tungsten to water to hydroxylate...

04 February 2020 4,677 2 View

Is it possible to perform a meta-analysis for an index value?

Dear researcher community. I want to ask if it's possible to perform a meta-analysis in an index, I mean, in value without standard deviation. For instance, in the regression model, many indexes...

04 December 2019 3,797 1 View

PLS-DA or LDA for NIR analysis?

I was wondering, for discrimination or classification propose is better use LDA instead PLS-DA in NIR data?. What analysis will works better in this kinds of data?. And why? Thanks so much in...

15 October 2019 8,409 8 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View