What are thermodynamics equations for folds in polymer crystal? How can I find them exactly?

More Nasrin Shahmiri's questions See All

Hi, I have a question? Why Young's Modulus doesn't have scientific value after 300% strain in stress strain curve for synthetic rubbers?

where can I find thermodynamic equations for explanation of this phenomenon? Please guide me.

09 October 2017 2,368 2 View

Why abrasion resistance of Polyurethane is 10 times the steel?

how can I find its charts and equations?

09 October 2017 6,460 4 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to prediction 2D to 3D aptamer?

Hello, I have a little problem. Well, right now I only have the DNA aptamer sequence. I went to see the 2D model form with DNA folding. After that, I used RNA Composer to simulate in 3D and used...

30 July 2024 6,794 0 View

Is it possible to manufacture polypropylene sheets using a biaxial process?

I know that films and other low-thickness laminated products are produced using biaxial orientation, but is there something similar for sheets with a thickness of around 6 mm? Or are they...

21 July 2024 1,559 1 View

Why am I seeing only one initial maximum in torque-time curves for the fusion of PVC in a Brabender?

We're studying the stability and fusion behavior of multiple PVC compounds in a Brabender. After a few trials, we set the temperature at 195 °C and the rotor speed at 70 rpm. Samples differ in...

12 July 2024 2,768 1 View

What is an ideal threshold value for log2(fold change)?

Hello everyone, I am performing differential gene expression analysis and I am not sure what is an ideal threshold for log2(Fold change).Thanks in advance!

09 July 2024 1,437 1 View

How can the alleged contradiction in the second law of thermodynamics and Carnot's theory be explained, and what are the current scientific responses?

The diagram suggests that there is a contradiction within the second law of thermodynamics and Carnot's efficiency theory. According to the second law, Carnot efficiency is independent of the...

08 July 2024 7,478 4 View

Unexpected Increase in R² for the Third Component in sPLS model?

Hi everyone, I'm performing a sparse Partial Least Squares (sPLS) model to understand if the analysed contaminants (55 individual contaminants) explain my response variables (42 response...

07 July 2024 2,333 0 View

What is the reason of appearance of 2 or 3 peaks in zeta potential analysis of sample?

Hello I have prepared metal nanoparticles and did zeta potential. Normally there is a single peak in sample but now there are 3 peaks. I prepared sample for analysis first I prepared 10 mg/mL...

30 June 2024 1,063 4 View

What does the area under the curve signify in dielectric loss tangent studies for solid polymer electrolyte ?

In solid ceramic electrolyte what is the Physical significant of area under the curve in dielectric loss tangent studies ??

23 June 2024 4,354 1 View

Difference between creep deformation and stress relaxation deformation ?

I understand the basic definitions of creep and pressure relaxation. However, I am confused about the exact difference between them. See attached photo. Because a compression force is applied,...

17 June 2024 5,344 2 View

Abdelkader BOUAZIZ

Dear Nasrin,

they are available in most polymer physics books. In the forthcoming days I'll try to provide you with at least one book (if it is not volumunous to be attached. Regards

Nasrin Shahmiri

Hi. Thanks very much .

No thanks. Would you please check the following link. Sooner I'll provide you with more documents. Regards

https://www.researchgate.net/publication/229874280_Crystallization_of_short_aliphatic_polymer_chains_I_General_chain-folding_behavior/amp

Dear Abdelkader BOUAZIZ,

Thanks very much for your help.

Regards

I have other volumunous books that I could not attach. Best Regards

Hi ,

I followed the link of article you prepared in your answer and it was really helpful and I downloaded some other related articles in this field.

Thanks so much for attention.

Nice and good luck. Regards