How to simulate a new protocol in VANET Toolbox in MATLAB?

I've downloaded the VANET Toolbox in MATLAB, but there aren't any detailed documentation on how to use it. Can anyone please explain the step by step process in designing the simulation...

01 November 2020 7,262 2 View

Which simulator other than NetSim is easy to build VANET sims? How to implement a MAC protocol and analyse the throughput,transmissions?

I have an assignment where I have to implement a latest protocol in VANET and analyse the results. I have chosen the OCA-MAC a TDMA based MAC protocol. Which simulator is easiest to implement...

01 November 2020 518 3 View

Effect of excess cyclodextrin on drug after cyclodextrin reaches maximum solubility in phase solubility study?

I am working on phase solubility studies between beta-cyclodextrin and drug? I used more concentration of beta-cyclodextrin till 30mM despite its maximum solubility of 16mM. Usually, above maximum...

30 October 2020 3,921 9 View

About Input factors which has chosen for wear examination?

1. Why 5, 10 and 15% of SiC was chosen? any base reference paper related to it. Why not below 5% is to be included. 2. What will be the result if the % of SiC is reduced less than 5% in wear...

27 October 2020 6,635 2 View

Is there a way to implement a large strain viscoelastic material model in AUTODYN?

I am new to AUTODYN and have used a little bit of ANSYS workbench. I have been looking at implementing a visco-hyperelastic constitutive model in AUTODYN. However, I could not find any way to do...

12 October 2020 5,245 3 View

Is a physical theory and its mathematical interpretation describes the same at the most fundamental level?

No. At the most fundamental level, Interpretation of physical theory by mathematics may not be appropriate. The reason- "Suppose a Circle of radius zero and with theta(zero) radians. It is...

21 September 2020 8,124 8 View

Do zif-8 has absorbance?

Do zif-8 have absorbance? And after synthesis and purification, zif-8 needs to be stored in powder or can be dispersed in aqueous or organic solvents

13 August 2020 242 1 View

How to frame the title of the manuscript or research proposal or thesis?

I would like to request the eminent researchers to guide us, which phase of the research the title has to be framed and on what basis? Thanks in Advance

19 May 2020 1,984 11 View

What is the recommeneded hardness test for weld joint ( Rockwell-A or B or C , Brinell , Vickers).i want recommened answer with proper reason?

what is the recommeneded hardness test for weld joint ( Rockwell-A or B or C , Brinell , Vickers).i want recommened answer with proper reason. The weld sample is 5mm thick steel plate.

03 December 2019 7,043 4 View

Is there any experimental evidence or theoretical prediction of electromagnetic waves with velocity less than that of light?

It will be useful to deal with Extremely low frequency radio waves..

24 October 2019 9,061 9 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View