What are the information that are obtained from a load flow study?

05 May 2015 1 3K Report

The output of the load flow analysis is the voltage and phase angle, real and reactive power (both sides in each line), line losses and slack bus power

Badges
Science topic

More Ali Alizadeh's questions See All

The use of solar water heaters in the right places?

Please reply.

06 July 2015 7,062 6 View

How to Choose a bus as a general set like?

Please Answer.

06 July 2015 4,159 3 View

What other environmental benefits does wind power bring?

06 July 2015 1,712 0 View

Do solar cells to store energy?

Please reply.

06 July 2015 1,724 3 View

Does the wind industry depend on subsidies?

06 July 2015 7,185 0 View

The load models in the power system?

Please sites or text.

06 July 2015 9,307 2 View

What are positive sequence components?

04 May 2015 6,273 2 View

What is meant by positive, negative and zero sequence impedance?

04 May 2015 9,327 2 View

What is Jacobian matrix?

How the elements of Jacobian matrix are computed.

04 May 2015 939 1 View

Are solar panels that light down there?

Which is useful for the roof .

04 May 2015 1,428 1 View

How to determine positive-stained cells in FACS? Use isotype or unstained control?

To compare positive and negative cell populations in flow cytometry, should I compare unstained cells with antibody stained cells? Or with the isotype control? Most papers show comparison with...

06 August 2024 6,728 6 View

Why do we equate male and female arousal?

Women, on the other hand, can become physically aroused (increased blood flow in the reproductive organs) without becoming psychologically aroused even in the slightest. (Robert Weiss)

05 August 2024 9,537 2 View

How to make a Lateral flow control line more uniform?

We have a lateral flow test on Sartorius 140 NC. The conjugate is gold-monoclonal antibody. Using different control lines (GAM, protein A, protein G) we get a very strong leading edge with reduced...

31 July 2024 4,510 3 View

Suggestions for the Annexin V Positive Control ?

Hello everyone, I am currently using washed human platelets to stain Annexin V as a procoagulant marker. Additionally, I am staining with PerCP-CD61 to identify platelet cells. So far, I have...

29 July 2024 8,624 1 View

Why cannot i find my protein on cell surface after antibiotic selection of expressing plasmid?

I cannot confirm cell surface protein expression by flow cytometry even after transfection and antibiotic selection of cells. Does it take long for proteins to express on the cell surface? the...

28 July 2024 3,178 3 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

Flow through curved domains?

Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...

25 July 2024 9,058 4 View

BD Cell Viability Kit - TO evaporation?

Hello, I'm conducting flow cytometry experiments using the BD Cell Viability Kit and I've noticed that the TO solution ends much faster than the PI solution. I store the solutions according to...

22 July 2024 2,257 0 View

Can I use CCCP instead of H₂O₂ as a positive control for ROS measurement through flow cytometry?

I am giving starvation stress to the soil amoeba (Dictyostelium discoideum) cells in my study groups and using NAC as a negative control. I am using DHE for ROS measurement.

20 July 2024 6,354 0 View

I came across oscillations in a pressure profile for a pipeline flow along the axis of a cylinder, how do I prove that these are not numerical err?

In terms of CFD, we often analyze the stability of the error using Von-Neumann analysis, especially for FDM based problems. Should we follow the same approach for a compressible fluid flow using FVM ?

13 July 2024 6,296 5 View