11 November 2017 3 353 Report

Hello I wanna start writing a CFD code but I have to use a simple guide..

Thanks

More Ahmed S. Mansour's questions See All
How do we correctly setup the solar ray tracing for a Photo Voltaic PV panel simulation in ANSYS FLUENT?

Hello, I have a simple model (PV cell+ air channel) and I do not know how to let the sun rays hit the PV surface and then transfer the heat to the air..What I see is the sun rays hit the air...

08 September 2019 688 2 View

What are the equations of the boundary layer of a flat plate that TDMA method is based on?

Hello, I need the equations that show the coefficient of the matrix that solves the velocity contours of the boundary layer over a flat plate. I have the explicit discretization equations but I...

05 June 2019 8,078 4 View

How to define a heat flux and convection coefficient at the same time on a wall using user defined function in FLUENT?

Hell, how can we write a UDF to include a heat flux value + convection coefficient for a wall in Fluent because we cannot define two named selections for 1 wall ? Danke!

05 June 2019 7,188 12 View

How can we define a symmetry wall boundary condition in Fluent?

Hello, I want to simulate the half of the domain and define a symmetry wall because I do not want to consider it as the edge wall, I want to consider it the wall at the half of the domain..How ca...

04 May 2019 6,100 3 View

How to use Chemkin to model the model studied in the attached paper?

Hello, I want to know how to use ANSYS Chemkin to model the attached model in the attached paper. the videos on internet are so simple. Thanks

04 May 2019 4,064 2 View

Can we cople between ANSYS FLUENT and Simplorer ASAP?

Hello, we have done a simulation using ANSYS FLUENT, can we couple it with ANSYS simplorer? And if yes, how and what are the documents I can study? Danke!

03 April 2019 2,799 6 View

How can we define a heat flux boundary condition + convection for one wall in ANSYS FLUENT?

Hello, I have a wall which is affected by a heat flux and it is cooled by convection..How can we do this in FLUENT? Thanks

02 March 2019 6,112 4 View

What are the equations used to simulate a steady state thermal analysis using FEA ANSYS thermal?

Hello, we wanna write a thesis and we need the equations used for simulating the temperature distribution over a PV panel.. Where can we get these equations that ANSYS uses ? Thanks

31 December 2018 5,908 5 View

How can we save calculations to a text file from a Matlab CFD code during running the code like ANSYS FLUENT?

Hello, we have a CFD code written in MATLAB and we wanna save the calculations at a specific node to a text file like ANSYS FLUENT..Any suggestions please? We will be extremely grateful! Thank you!

31 December 2018 934 3 View

How does this UDF of a flap airfoil work?

Hello, I have this UDF and it says that the airfoil changes the degree to +/- 8 through 1 sec, how is to work and how can we control the angle? /**********************************************/ /*...

09 October 2018 4,673 0 View

Similar questions and discussions
How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Request Python code?

Request Python code from this article : Gender equity of authorship in pulmonary medicine over the past decade. THANKS!

08 August 2024 6,242 2 View

Why does everyone use vs code?

Visual Studio Code (VS Code) has become a popular choice among developers for several reasons: 1. **Free and Open Source**: VS Code is free to use and open source, making it accessible to...

07 August 2024 7,013 4 View

How can i do multivariate Time Series forecast using MLP, ANFIS and LSTM?

I need the python code to forecast what crop production will be in the next decade considering climate and crop production variables as seen in the attached.csv file.

05 August 2024 2,977 3 View

Do you know any references for analyzing stochastic fiber orientaion composites ?

Hello everyone I am looking for one or some books for propertes and behaviors of stochastic fibre orientation composites. unfotunately I could not find any suitable reference for thias by...

04 August 2024 3,461 3 View

How to report results of Generalised Linear Mixed Models in a journal article?

Hi everyone, If you have written or come across any papers where Generalised Linear Mixed Models are used to examine intervention (e.g., in mental health) efficacy, could you please share the...

04 August 2024 4,130 4 View

The question is how to use Wavenet transform?

HOW CAN I WRITE A CODE TO USE THE WAVENET TRANSFORM AS A FEATURE EXTRACTION METHOD INSTEAD OF DWT IN MATLAB?

03 August 2024 7,829 0 View

PhD thesis topic?

I want to write a topic for my PhD thesis in hospitality (hotels), can u please suggest some variables

29 July 2024 9,058 3 View

What are the main types of errors and causes that English major college students commit in their English writing?

a 15-page paper

29 July 2024 1,956 5 View

Are you interested in contributing a book chapter on biomaterials in Orthopaedics?

I am editing a book for Springer Nature on recent advancements and future trends in biomaterials for orthopedic and trauma applications, with a publication date slated for early next year. If you...

29 July 2024 5,015 9 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close