Writing LP modes in mathematical form?

Dear Colleagues Hope you all will be fine The optical carriers can be written in mathematical form as shown in attached figure.Please let me know how we can write/show linearly polarized LP modes...

06 July 2019 5,633 3 View

Data rates in WBAN?

Dear Researchers Please let me know the typical maximum data rates (Mbps) supported by wireless body area networks (WBAN).If possible then, please share relevant citation/research paper. I will be...

04 May 2019 410 2 View

What is the optimum emission level (PSD in dBm/MHz) in Green Radio (GR) trend compatible wireless systems?

In order to protect the environment from harmful exposure of electromagnetic radiation emitted from current wireless and cellular networks, network designers are regulating the emission power at...

31 December 2018 2,285 0 View

Latex fails to show .eps figures after generating the pdf document?

I'm trying to generate a document with .eps figures but after compiling the TexWorks, i am not getting any figure on generated pdf file of the document but only the caption of the figure with...

31 December 2018 2,291 1 View

Non-linear chirp induced by noise over cw signal in HNLF?

Dear Friends Please refer me to a journal paper/research article where chirp is induced over CW by noise in HNLF (Highly non-linear fiber). regards

04 May 2018 1,244 3 View

Lowest attenuation and mode dispersion?

Dear Friends Please comment at which wavelength ( 850nm or 1300nm) gives lowest model dispersion and fiber attenuation for optical transmission over multi mode graded index fiber? I am highly...

02 March 2018 6,156 4 View

How to vary chirp shape along the pulse?

I am attaching a picture of the chirp shape(which is up-chirp i.e increasing along the pulse like a slope in RED COLOR).I am getting chirp in CW probe by exploiting XPM in HNLF by data modulated...

11 December 2017 9,451 3 View

What is the UWB Electrical Signal?

Dear Respected Mentors,Researchers and Colleagues With reference to the paper attached herewith,Please make clear the highlighted text in yellow color. We generate the UWB mono-cycle or doublet...

10 November 2017 695 5 View

FWHM of Regenerated Gaussian Pulse

Dear friends plz let me know the mathematical relation of bandwidth of optical bandpass filter(OBPF) with FWHM/Pulse width of optical gaussian regenerated pulse at OBPF output??? i will be very...

06 July 2017 886 8 View

Request to help me in Phase Modulation to Intensity Modulation Conversion

Dear and Respected Colleagues I am requesting to all those respected mentors and researchers working on Optical Communications Please help me on PM to IM conversion to generate UWB pulses?????

06 July 2017 484 2 View

What are anisotropic electrical and optical properties of a semiconductor due to?

In some materials, properties such as band gap, thermal conductivity differ along different crystallographic axes. What are the basics?

01 March 2021 1,923 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

Mediation path analysis - Can I run two seperate models?

I am wanting to run a serial mediation model with 2 x IVs, 2 x MVs, and 3 DPs (all continuous). Is it problematic to run 2 different models for each IV, keeping the MVs and DPs the same in each...

27 February 2021 5,681 3 View

How can we limit artifacts caused by rotation in fiber photometry?

We are trying to run fiber photometry experiments for long time scales, but we get these sinusoidal artifacts that come up. We think they may be caused by twisting of the fiber optic subject...

25 February 2021 568 1 View

No title

25 February 2021 5,713 1 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View

Physical-chemical formation of stalactites/stalagmites. what promotes the formation/growth of these structures?

I know, or think I do, the basic idea behind these natural structures, as from what I know they form due to water dripping from the top leaving a salt deposit behind. But started to wonder about...

22 February 2021 1,400 4 View

How can we add reinforced thermoplastics with granules in injection molding machine?

I need to make an injection molding machine in which short fibers are to be introduced. Short fiber length and material properties are to be determined and also the material strength are to be...

22 February 2021 4,290 1 View

Is there a suitable way to confine cell attachment area inside a multi-well plate?

Are there any types of cylindrical cell culture inserts that are designed to confine cell seeding area? Say, if I'm using a 12 well plate (3.5 cm^2/well), but only want to seed cells in the middle...

22 February 2021 7,127 4 View

How to resolve Gaussian error termination " Error termination via Lnk1e in F:\G16W\l103.exe" for TS(QST3)?

When I run the job for TS(QST3) in gaseous phase, it was completed without any error. But when I add water in CPCM model it terminated with an error: Inconsistency: ModMin= 2 Eigenvalue=...

21 February 2021 3,198 2 View