Using abaqus, How to excite a plate with pure mode S0???

Haider Rizvi @Haider_Rizvi10

09 September 2019 1 6K Report

Romik Khajehtourian

Hi Haider, this paper explain isolating a pure mode:

https://lib.dr.iastate.edu/cgi/viewcontent.cgi?referer=https://www.google.com/&httpsredir=1&article=3721&context=qnde

Applying it in abaqus should be straight forward.

Badges
Science topic

More Haider Rizvi's questions See All

How to reduce signal noises?

I am trying generate guided waves on simple metallic plate through piezo-ceramic material, I place two piezo on the surface of the plate at the different location and through Arbitrary pulse...

09 October 2019 4,706 3 View

How can I generate image from Delay and Sum algorithm?

I am trying to find the pixel vales by using DAS algorithm, I have calculated the envelope of the signals by using Hilbert transform and then calculated the arrival time of a signal traveling from...

09 October 2019 3,581 1 View

Where does this extra wave come from?

Using Abaqus, I am trying to generate symmetric lamb wave mode in a simple Aluminum plate by applying symmetric point force parallel to the plate. The extra wave followed by the S0 mode appears...

08 September 2019 5,265 3 View

Confused over complex representation of the wave?

I am trying to derive the general equation of lamb wave. My book says that y = Aexp(i(kx−ωt) is the general equation of simple harmonic wave propagating in +ve x direction. but I am confused with...

31 December 2018 8,586 4 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Is changing the medium during the experiment overestimate the results?

I am experimenting with cancer and non-cancer cells in a 12-well plate for 4 days with a seeding density 1*10^4/well, however, I noticed that the control group growth rate slows down on D3. Should...

07 August 2024 2,283 2 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

How can I improve the quality of lamb milk replacer for machine feeding?

Hello everyone, I am researching ways to enhance the quality of lamb milk replacer for machine feeding. I would appreciate any insights or recommendations on the following: Manual vs. Machine...

06 August 2024 6,227 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Can you recommend a 96-well plate for minimal cell adherence to the wells during phagocytosis experiments?

I have been performing short phagocytosis experiments using 96-round bottom, tissue culture treated, well plates (Falcon, 353077). I culture the cells with the phagocytic cargo for 2-4hrs, wash...

04 August 2024 5,228 4 View

PBMC infection with virus?

In my study, I intend to infect PBMCs with SARS-CoV-2. After that, I will analyze NK cells by flow cytometry to see if their phenotype changes or if they show degranulation. After the infection, I...

01 August 2024 4,403 4 View

Found this object in the cell culture - do you have any suggestions what it might be?

Dear researchers, Today, we found this object in one of the wells of a 96wp culture plate. The plate contained MEC-1 cells and GelTrex. I am quite curious what this is (because it's not cells). Do...

01 August 2024 2,250 2 View