Transparent piezoelectric KNN ceramics

01 January 1970 0 6K Report

Is it anyway possible to get a transparent ceramic pellet via normal conventional sintering instead of using pressurized sintering (as in hot press)?

Badges
Science topic

More Tarun Yadav's questions See All

• What the possible Persistent Organic Pollutants and Heavy metals present in fluorspar, sediments, and water bodies around its mining area?

Approximate concentrations are require in compared with the WHO permissible limts

11 August 2024 2,723 1 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

Is Galaxy.org good to use for research for analyzing data and for publication?

Hello all, I wanted to know, can I use galaxy (USA, Europe or Australia) platform for analyzing the shotgun data, and can it be used for publication purpose as well? Thanks :)

06 August 2024 6,610 4 View

Polymer wear calculation?

What is the method for analytically calculating the wear and service life of polymer-polymer sliding pairs?

04 August 2024 1,078 1 View

How to convert g/kg Humic acid dose to kg/ha?

I used humic acid at 0.044 g/kg soil in my pot experiment. But finally, I have to recommend kg/ha. Each pot's soil weight was 11 kg. What is the solution?

02 August 2024 7,186 6 View

How to select target material for X-Ray generation?

Generally, the target material is Mo, Co, Cu, Fe, Cr, etc, so on what basis should we choose this material?

31 July 2024 5,824 0 View

Why Powder XRD is performed after cruhsing a crystal if Single Crystal XRD analysis of the same crystal has been performed already ?

What information we can get from PXRD analysis other than from SCXRD analysis of a crystal ?

30 July 2024 6,261 4 View

Why is it not common to see similar pairs in polymer sliding pairs?

If the pairs are similar, will it reduce the adhesion due to electric charges?

29 July 2024 3,185 2 View

How to use differential equations to apply hybrid production in an inventory model ?

give suggestions

22 July 2024 5,664 2 View

How to determine LOD values?

I am performing fluorescence experiments using a ligand to detect metal ions. I want to determine the Lowest Detection Limit (LOD) using the formula LOD = 3σ / K. However, I'm uncertain about...

19 July 2024 1,086 1 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Non -oxidizing metal binders?

I'm trying to sinter some Nb parts and I'm trying to find a binder which does not produce oxidative compounds when it decomposes.

25 July 2024 9,823 3 View

Does it exist some special technique for cutting ceramic membranes for Cross-sectional FESEM images?

Does it exist some special technique for cutting ceramic membranes for Cross-sectional FESEM or SEM images?

25 July 2024 5,482 2 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

How does the crystallite size and microstrain distribution influence the mechanical properties of a ceramics?

10 July 2024 3,444 4 View

Hey there, What is The best recommended solvent( safe for use) to dissolve or remove Z-90 Adhesive from ceramic surfaces ?

as of my knowledge z90 is acrylic based sealant adhesive.

09 July 2024 8,660 4 View

How to change the author?

Hello! Research of factors affecting thickness of the covering obtained by electro contact sintering of composite materials. This is my article, not Varvara. How to change the author? Incorrect...

09 July 2024 3,829 0 View

Can some indicate a technique - or approach - to measure the thickness of a 20µm film and thickness with water uptake?

Hi, I need to measure the real-time (or temporal intervals) thickness variation of a transparent material from dry to wet/humid conditions, however, I cannot use the following techniques: -...

08 July 2024 4,799 4 View

Is there a subtle distinction between the terms "substitution" and "doping"?

Dear Prof, is there a subtle distinction between the terms "substitution" and "doping" when referring to modifying ceramic dielectric materials for example Na0.5Bi0.5TiO3? Is there any difference...

08 July 2024 2,043 3 View