TPU fibers delamination from cotton fabric - problem solution?

More Sheraz Ahmed's questions See All

I have get this error when i calculated the geometrical optimization for prco3, it takes 12 hours until gives this message in the outputfile?

Fatal error in MPI_Allreduce: Other MPI error, error stack: MPI_Allreduce(1628)......: MPI_Allreduce(sbuf=000002459254A180, rbuf=000002459F86A140, count=4851, MPI_DOUBLE_COMPLEX, MPI_SUM,...

09 August 2024 7,615 1 View

Why Do TDS and EC Increase with Larger Wastewater Volumes, While BOD and COD Decrease?

I have carried out MFC experiments on three different volumes, 50, 500 and 1000 mL of wastewater. Results after MFC treatment shows that TDS and EC are more in larger volumes of water i.e. TDS and...

09 August 2024 9,621 0 View

Is this a facetotecta nauplius?

This larva was captured using a plankton net in the Persian Gulf during the summer. I believe it may be a Facetotecta nauplius.

08 August 2024 3,746 4 View

How to set the environment variable for incorporating the GD3 dispersion in G16 for performing calculations using the OPBE functional?

I have incorporated the dispersion effect for the OPBE functional by specifying the S6, SR6 and S8 parameters for GD3 in Gaussian G09 package. For this purpose, I have defined the environment...

05 August 2024 1,494 2 View

How prion can cause disease?

how is prion can cause disease

01 August 2024 250 1 View

Has anyone used Jump 2 before?

Jump 2 is the 1st app scientifically developed to measure your jump height.

31 July 2024 8,194 0 View

Help on understanding the implementation of Mori Tanaka method on MATLAB?

I am new to Micromechanics and having similar problem with understanding the implementation of the formula's. I would appreciate if anyone can guide me on how to go about getting a scalar value...

30 July 2024 969 0 View

Following click reaction in cell lysates, protein is immobile and remains at the top of the gel in SDS-PAGE?

I am using CuBr/THPTA for a click reaction in total cell lysates. I am facing issues with my protein sample in non-reducing SDS-PAGE where it's not migrating properly and most of it remains at the...

29 July 2024 950 4 View

Which filtration method to go for run off water from dirty solar panels to be used again?

We are working on a robot that cleans solar panels using fresh water supply and a rotating brush. We are trying to conserve as much water at possible by recycling the dirty water that is collected...

28 July 2024 5,778 2 View

I need a reliable source or an example supported by excel sheet to understand Fuzzy Vikor?

27 July 2024 5,916 1 View

RNA Extraction Using Hot Borate Method No Longer Working?

I've been performing RNA extraction on cotton petiole tissue for a few months now using the method described in the following paper, a derivative of the typical hot borate method...

08 August 2024 9,882 2 View

How can the rubber fibres produced by the electrospinning device be removed from the fibre collect(aluminium foil) ?

How can the rubber fibres produced by the electrospinning device be removed from the fibre collector (aluminium foil) without affecting the orientation of the rubber fibres for use in reinforcing...

26 July 2024 8,281 0 View

How to get LP fiber modes directly from Comsol?

Hi there, I'm new to modelling with comsol. I would like to ask if it is possible for comsol to output linearly polarized (LP) modes? I tried modelling a simple single mode fiber with an enlarged...

23 July 2024 4,019 3 View

How do you decide an optimal AC amplitude for non-faradaic electrochemical impedance spectroscopy?

I work with planar interdigitated electrodes (IDEs). The finger width and the spacing between the fingers are 5 micron. The surface of the IDEs is coated by a non-conductive polymer layer...

16 July 2024 5,031 1 View

How to solve Bubble Error in fiber splicing?

I'm having a bubbling error while splicing 100/350 um optical fiber (core/cladding) on the Fujikura FSM100P+. I have tried some ways such as changing Prefuse power and Prefuse time but to no...

03 July 2024 7,463 6 View

Why does my Modified Gomori Trichrome (LG) Stain muscle fibers red, and how can I improve it?

I am trying to visualize Nemaline Rods in Skeletal Muscle fiber cross sections. I have read about 10 different gomori protocols, and the protocol seems very straightforward. Every paper I read on...

27 June 2024 5,423 2 View

Can i use polystyrene as a matrix in a hybrid COMPOSITE?

fiber powders will be used as a reinforcement.

23 June 2024 10,027 3 View

Why PLLA deposited by gap electrospinning lose piezoelectricity?

I tried to prepare aligned PLLA nanofibers by gap electrospinning method. But after the deposition, when I tried to measure its piezoelectric sensitivity, it actually did not exhibit any...

17 June 2024 9,763 0 View

Which solvent and substrate is found to be best suited for deposition of electrodes with MXene ink?

Suppose we have dried MXene slurry (Ti3C2Tx), then the combination of which solvent (in which this dried MXene slurry powder will be mixed, subsequently forming the "ink") and corresponding...

13 June 2024 5,763 0 View

Propose a comprehensive plan to design the new telecommunication system for the company, considering the following aspects:?

a) Design a scalable and robust network architecture that can handle the increasing data traffic and support various communication technologies. b) Recommend suitable transmission technologies,...

10 June 2024 2,187 1 View