Plant molecular biology ?

I want to add 1 ug or (1000ng ) of Plasmid DNA in a reaction mixture and add water for a final volume of 50 ul. my plasmid DNA a concentration of 68.47 ng/ul in which I have total DNA volume...

22 September 2020 7,325 6 View

Can any one suggest me an algorithm for storage optimization?

I want to ptimize super capacitor and battery storage in solar solar resource.

17 August 2020 4,188 6 View

...about correspondent author?

Dear all, Does being a correspondent author matter or what if a PhD research paper published with a supervisor as a correspondence author?

05 April 2020 5,639 12 View

How much of mineral element can be served by a portion of food in comparison to recommended daily intake?

The mineral contents were calculated for a certain grains in their raw form. How can we calculate how much a given mineral, say; zinc or iron can be served by a portion of the flour sample per 100...

15 August 2019 4,731 2 View

What is the appropriate stastical software to analysis for scale data collected from infected(inoculated) and control group(non infected) of plants?

I was collected my ten scale level data from from infected and control(non inoculated) by plant pathogen. Therefore, which statistical tools is appropriate for my data analysis?

09 February 2019 6,854 9 View

How to solve the following?

Consider 1 m3 of the soil surface soil. The soil is in good condition and has 0.45 mineral matter, 0.05 organic matter, 0.2-soil solution, 0.2to0.3 air and 0.3 to 0.2-volume fraction. 1. What is...

16 January 2019 1,757 1 View

Which statistical analysis software is best?

Dear Colleagues; Now a days there are different kinds of statistical tools are available (for example SAS, R, Minitab, SPSS, Genstat, MATLAB etc.) for analysis of research data. Therefore, my...

06 November 2018 8,850 44 View

What is the general behavior in relation to the correlation between the protein content and the fat content of plant foods, specifically legumes?

There are various arrays of trends and interactions between nutrients in a given food sample. The correlation between some of them is clear, as evidenced from my own result while working on the...

09 October 2017 4,377 4 View

What do the following ratios indicate in phytochemical and antioxidant study?

What is the implication of the ratio of TFC/TPC in phenolics analysis and antioxidant potency composite (APC) index? In quite a large number of articles, the TFC/TPC is estimated to be less than...

20 September 2017 2,234 2 View

Which one is the best and recommended for Protein purification and characterization?

Which one is the best and recommended for Protein purification and characterization? a) Salting out (Ammonium Sulfate precipitation(NH4SO4)) b) Ion-exchange Chromatography c) Gel Filtration...

01 January 1970 7,322 8 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View