Tensile strength test for concrete cylinder?

More Najia Saleh's questions See All

In DFT or HF, is it more expensive to calculate the H matrix or to diagonalize it?

I was wondering: in common DFT (or Hartree-Fock) algorithms/codes, and in particular in solving the Roothan equation, what is the most computationally expensive part: 1- evaluate all the terms of...

01 February 2021 396 2 View

Warning in Lavaan, variance-covariance not positive definite!, model is not identified?

Dear colleagues, I am new to R, I have been using Amos for conducting CFA but came to learn that when dealing with Likert scale, Lavaan in R is a better tool to do such analysis. I started using...

30 December 2020 5,608 3 View

How can i figure out whether nanoparticles in my synthesis crosslinked or not?

i prepare protein nanoparticles. in one of my synthesis i use trifle amount of crosslinker and the nanoparticles stick in the bottom of plate. how can i understand that nanoparticles become...

03 December 2020 559 8 View

What is the best solver in OpenFOAM to study melt-water interaction?

During a severe accident in a nuclear reactor an energetic molten fuel/coolant interaction could happen, where a multiphase flow of a steam-water mixture in a region which contain drops of a...

29 November 2020 8,376 2 View

How can we define columns in 3D PLAXIS model for buildings existing near the excavation?

I started by a model using 3D PLAXIS to study the effect of deep excavations on existing buildings. The building was simulated as a surface plate with a surface load. Now I'm trying to do it as a...

29 November 2020 3,198 4 View

How to read forces from a file and apply them to a specified nodes in ANSYS APDL?

I want to apply different forces for every node. These force values are saved in .txt or .csv file. Can anybody help me to do that using APDL command. I attached Ansys input file for my model and...

15 November 2020 2,883 1 View

Where can I find off targets for Apis mellifera?

I would like to find off target sites for my sgRNA, however the more commonly used off target finders do not include apis meliifera, is there an application or website that would allow me to do...

09 November 2020 3,463 1 View

What is the best method to sterilize hydroxyapatite nanoparticles?

Powder insoluble

08 November 2020 509 3 View

Wrong cell dimension (cosAB)?

All input files with bravais lattice that contains an angle doesnt run in my Quantum espresso. i even tried running them in my friends laptop but the crash file displays the same problem. i hope...

03 November 2020 2,722 1 View

How Abaqus can generate lumped mass matrix with non zero values only at the diagonal ?

Hi everybody I generated mass matrix by Abaqus, but it has nonzero off diagonal values. I need to get lumped mass matrix with nonzero values only at the diagonal. In Ansys I can turn Lump on...

28 October 2020 5,960 4 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Apart from Nanosilica and CNT's what are the other nanomaterials readily available to use in concrete mixture?

Nanotechnology in concrete materials

01 March 2021 3,379 3 View

Is anyone familiar with the cyclic compressive fatigue testing (BS EN 12697 - 25) ?

I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...

28 February 2021 2,004 3 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View

Compute for the total volume of concrete needed for the concrete pouring of the foundation including its column up to NGL only as shown in the plan?

Looking for the quantity of cement, sand, and gravel of footings and columns. Thank you!

25 February 2021 3,092 2 View

Can we recognize signs of the "volatility clustering" property of a time series in its time domain plot?

My purpose is to recognize the volatility clustering property without statistical tests such as The Lagrange Multiplier (LM) test.

24 February 2021 4,150 3 View

Ahmed I. Ramadan

Approximately 0.02 - 0.1 MPa. You can follow this link, it is useful:

http://theconstructor.org/concrete/splitting-tensile-strength-test-on-concrete-cylenders/2116/

Najia Saleh

Thank you alot

Deepak Kumar Diwakar

Apply the load continuously without shock at a rate of approximately 14-21kg/cm2/minute