What will happen if a hollow iron pipe is used instead of solid iron rod in concrete?

I want to know what is going to happen to the hollow iron pipe if it is used in concrete? It will get compressed?

07 August 2018 548 6 View

Latent heat of petroleum ether?

Anyone knows the latent heat of Petroleum ether?

02 March 2018 7,031 2 View

How can the boiling point of petroleum ether can be determined at sub atomic pressures?

Anyone knows the way to find out the boiling point of petroleum ether or any other liquid at various pressures?

02 March 2018 7,783 2 View

Can anyone suggest the easiest method to learn fluent?

CFD

07 August 2017 6,356 6 View

Numerical modelling of heat transfer systems

Please suggest the books to learn numerical modellining of heat transfer systems for beginners.

06 July 2017 2,408 1 View

What is the best method to cool the miniaturized electronic devices?

Journal paper: A critical review of traditional and emerging techniques and fluids for electronics cooling

05 June 2017 6,006 3 View

Anyone knows the application of using a Phase Change Material (PCM) at the evaporator of a heat pipe?

05 June 2017 3,394 3 View

Graphene is available in solid form?

05 June 2017 3,752 11 View

Joining metals to non-metals

05 June 2017 7,899 3 View

Heat transfer applications of nanofluid

Anyone knows the practical applications where nanofluids are currently being used. Many researchers have reported enhancement in heat transfer with nanofluid. But, nanofluids are currently being...

05 June 2017 278 13 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View

Model Volume fraction and magnetic field applications of nanofluids in ANSYS?

Hi I am working recently on a project where I have to study how the thermal properties or heat transfer enhancement of nanofluids as the volume fraction changes, or if a magnetic field is applied...

22 February 2021 961 2 View

Help with assigning pressure boundary conditions in FLUENT on a large structure?

Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....

22 February 2021 9,972 4 View