Suggest few commercially available polyurethane mould release agents

Prashanth Thimma reddy @Prashanth-Thimma-Reddy

09 June 2017 0 3K Report

We are looking for Mould Release agents for polyurethane

Mould : Stainless steel ( heated to 100-140)

Substrate : water soluble Polyurethane dispersion

Application: To make Unsupported polyurethane glove

Processing method: Dip moulding

Badges
Science topic

More Prashanth Thimma reddy's questions See All

Dear all, Iam currently working on Dc Microgrid model for electrical vehicle charging. Can any body give good IEEE research paper on this topic?

please give any suggestion?

04 February 2021 4,837 5 View

What does the change in D-peak position in Raman spectroscopy of carbon materials indicates?

We have carried out high-pressure Raman characterization on some of our samples. After fitting, I have observed a change in D-peak position with increasing pressure. What does this change...

20 January 2021 853 3 View

PSFB control signal?

Hi everyone iam facing a problem to give control signal for switches in design of PSFB converter in matlab simulink. Anybody's help will be appreciated.

14 December 2020 6,021 3 View

What are the alternative to the pozzolanic materials to in concrete to enhance the durability of concrete?

As of now, Only industrial wastes were using as pozzolanic materials in concrete to enhance the durability of concrete. Can any once suggest me the alternatives of those materials?

11 October 2020 3,569 4 View

Can any one suggest me the dielectric constant of Gold and Co3O4 at room temperature ?

i have a question regarding dielectric constant of gold,cobalt oxide (co3O4) and n-tpe silicon . i find only one publication on this issue showing dielectric function cobalt oxide(CoO) 12.9 and...

02 October 2020 9,138 4 View

Eupergit beads for enzyme immobilization?

We are looking to immobilize some of our enzymes on Eupergit beads. I was wondering if you know any commercial supplier of Eupergit beads?

28 September 2020 5,664 3 View

Can somebody kindly suggest a good FEM software for the numerical solution of stochastic PDEs?

Please kindly suggest some good FEM softwares for the numerical solution of both time-dependent and time-independent stochastic PDEs.

28 September 2020 6,598 4 View

How to run Seismic analysis for the following model in OpenSees..?

I have developed a 3 bay 5 story 2D frame in Opensees but I have problems with element load and application of seismic load in Opensees using an acceleration file. I always got an error namely...

27 September 2020 5,885 4 View

How can we evaluate the conductance of a constant power load (CPL)?

Any CPL is modeled with a current source in parallel with negative resistance. How do we evaluate the negative resistance, if we know the constant power consumed by the load?

19 September 2020 6,188 3 View

How to learn the modelling of RC beam subjected to 4 point bending in Ansys Mechanical APDL?

I need to model a reinforced concrete beam subjected to 4 point bending. I also need to plot the load vs displacement at mid span and compare it with the experimental data. Bond between concrete...

10 September 2020 9,004 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View

How to separate water from glycerol solvent in a solvent recovery vacuum distillation column?

I am currently doing my third year design project. I have been assigned to design a glycerol recovery column in vinyl acetate monomer production. The process unit before the recovery column is an...

01 March 2021 9,525 4 View

What is the state of the drug inside solid lipid nanoparticles (SLNs)?

I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...

01 March 2021 3,703 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View