What do you know about "Stamped concrete"?what are the challenges make it no to be used instead of concrete blocks in walking ways ,garages,yards,etc.?
Stamped concrete lacks durability.
thank you so much Mohannad Husain
http://www.dot.state.mn.us/mnroad/reports/PDF's/coloredconcretedraft.pdf
When you use RIA, with a control the unknown sample with antibodies, you bare in mind the binding sites of the antibodies. However you still need to measure labelled antigen (radioactive) and not...
28 February 2021 2,133 3 View
We have always used the 96 welled plate, the 48 welled plate but apparently there is much evidence on the 24 welled plate and above all its benefits.It states it is the same you would use on ELISA...
28 February 2021 1,149 1 View
Hi, I am doing a review and hopefully meta-analysis for my Master thesis but I have the following problems: - Some studies only give the difference between end trial and baseline data and other...
22 February 2021 1,115 4 View
In my opinion, the RG site is useful in solving scientific problems and shows the researcher's ability. Besides, the separation of the H-index from the self-citations and the overall index is an...
22 February 2021 3,894 6 View
Hi, i am conducting a Monte Carlo simulation for my new distribution but the MSE values are increasing while the sample size increase, does any experience this issue before and what should i do...
22 February 2021 3,680 4 View
I have a basic knowledge on Python, R and MATLAB in analysing data. Among those, which is the best and user friendly? Which one should I learn deeply to analyse data?N:B: I want to learn data...
20 February 2021 3,950 15 View
the samples are not completely soluble - just swelled the solvents that's mean the sample may be partially soluble any suggestion, please
16 February 2021 8,801 3 View
We collected faecal samples from various species that we want to analyse their microbial communities' DNA via Next-Generation Sequencing. The problem is that due to budgetary constraints, we will...
16 February 2021 5,466 4 View
Hi, If I am performing an MD Simulation in which the two groups/molecules are moving in a direction on applying a force on the system, how would I calculate the velocities/acceleration of the two?...
08 February 2021 9,525 4 View
When you use RNAseq I understand that it must follow certain conditions when you use it. One of them is the insertion of a polyA tail. The insertion of the polyA must include then...
05 February 2021 3,770 4 View
I have an experiment with 28 participants The independent variable is the times 1, 2, 5, and 10 used as the cross hairs during a task These 4 times were tested using 4 different blocks, each...
03 March 2021 9,692 2 View
can anyone help me in this, it will help me with my research work
01 March 2021 834 3 View
I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...
01 March 2021 736 3 View
Nanotechnology in concrete materials
01 March 2021 3,379 3 View
I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...
27 February 2021 6,801 3 View
Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...
26 February 2021 4,026 5 View
In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...
26 February 2021 3,806 2 View
Looking for the quantity of cement, sand, and gravel of footings and columns. Thank you!
25 February 2021 3,092 2 View
Colleagues, I have been using ANSYS to model concrete strengthened FRP sheets, but less than happy with it. Any has recommendation for efficient, easy to use FE program for modelling concrete...
22 February 2021 7,528 3 View
Hi I am running a simulation in Abaqus for a concrete beam. Its fine aggregate replaced with sea-sand. I was wondering if I could find studies that measured the ultimate strain of concrete made...
22 February 2021 6,409 2 View