Actually these are low carbon steels.
I have a feed alone as one of the layer. When i try to extract that, I get the folloing error. Kindly help me , how to resolve the issue and extract the gerber file
29 February 2024 3,772 2 View
The emulsion of my sample has 0.08 polydispersity with an average size of 130 nm and only one peak (100 % intensity) both in DLS and MADLS. Nevertheless, I see two zeta potential populations....
20 February 2024 2,636 4 View
can Bavistin be incorporated into microalgae media against fusarium?
20 February 2024 3,488 0 View
under the addition of antifungal, the microalgae did not have significant green pigment in the petriplate and cells looked bleached in petriplate. on microscopic analysis few cells were found to...
20 February 2024 6,788 0 View
If the total mass is interdependent, then does the total mass contain both matter and antimatter masses like this: Mass = Matter × Antimatter. E.g. (hypothetical), The Proton's mass ==...
17 January 2024 9,945 3 View
In panel data estimation if t=20 and i=20, do we necessarily need to test for stationarity, co-integration and causality. What is best method to estimate the model with this data set, if one is...
30 November 2023 6,086 0 View
I pioneered the courses on Start Your Business and Grow Your Business in India as Chairperson, Center for Entrepreneurship, SPJIMR, Mumbai. My colleague at SPJIMR , Dr. Nirja Mattoo set up the...
30 October 2023 5,805 2 View
for monitoring disinfection byproducts in drinking water
12 October 2023 8,613 3 View
We can use EDX to measure the silver concentration before and after leaching test to know amount of silver leached. However, the concentration of leached silver from membrane is measured using...
09 September 2023 8,339 1 View
Suitability of Soil Sustainable alternative to Stabilizer and soil Pre and post construction issues and difficulties Durability of recent earthen construction
04 September 2023 9,749 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,989 3 View
is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it
06 August 2024 947 1 View
I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?
04 August 2024 1,537 1 View
A computational study of heat flux on cylindrical surfaces using CNT hybrid nanofluids
28 July 2024 4,985 1 View
I would like to conduct artificial sunlight experiments to mimic heat capture and air warming in a greenhouse system. The main objective is to heat up the temperature inside the greenhouse, not...
28 July 2024 4,006 2 View
I am an undergraduate mechanical engineering student seeking suggestions on topics related to either thermodynamics, fluid mechanics, heat transfer or renewable energy for my final year project....
24 July 2024 4,058 5 View
I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...
16 July 2024 3,212 5 View
Hello everyone, I am facing a consistent issue in my NMR spectra with an unwanted peak appearing at 1.25 ppm. This peak seems to vary with the amount of sample: it becomes more pronounced with...
15 July 2024 9,065 4 View
Heat transfer
06 July 2024 2,134 1 View