Hi I need 2020 6G and 2020 network coding references to cite soon in my 6G network coding paper ?

I have a paper at the last stage of publication on Q1 journal and I was asked to add 2020 references regarded 6G and network ciding

03 October 2020 5,177 3 View

How to use Tresca criterion in Abaqus VUMAT?

Hello, I know that Abaqus uses Mises yield criteria by default, and I have heard that if I want to use Tresca then I need to implement this in a VUMAT subroutine (for Abaqus/Explicit). I'm sure...

06 March 2020 2,435 3 View

Which software allows high quality schematic drawings for publications?

Hello, I have spotted a number of high quality schematic diagrams, such as the one attached here, from publications. Which software is able of reproducing such high quality schematic...

06 March 2020 4,460 3 View

Why does increasing strain hardening exponent result in less material necking?

Hello, According to the power law, Stress=K*strain^n. Could someone please explain why an increase in strain hardening exponent n results in less material necking from this equation? Please see...

15 February 2020 3,984 4 View

How do I make Abaqus stop the simulation once a critical value of PEEQ has been reached?

Hello, I am doing a series of metal forming simulations in Abaqus. I want the simulations to automatically stop when a critical value of PEEQ (or some other variable) has been reached, in order...

05 February 2020 5,114 4 View

How can I show through thickness stresses along a non-linear bending path in Abaqus?

Hello, I am doing a non-linear beam bending / forming analysis in Abaqus. I want to to get results for the stresses through the thickness direction, where the top fibre will be in tension and the...

17 January 2020 7,903 9 View

Why do I get different FE simulation results each time the solver is run?

Hello, i am performing a highly non linear metal forming simulation using PAMSTAMP FE simulation software. I have noticed that for the same mesh and boundary conditions, I get different results...

01 January 2020 1,074 4 View

What's the typical active area for anode and cathode for EIS test?

EIS, Active areas of Anode, Active area of cathode, SOFC

16 November 2018 3,137 4 View

What's the typical active area for anode and cathode for EIS test?

EIS, Active areas of Anode, Active area of cathode, SOFC

10 November 2018 8,856 5 View

Can Hedge's correction be run where I have a small sample size but repeated test (ie total output over 11 data points)?

How to run this on SPSS?

17 September 2018 2,519 1 View

Why does blocking with my immunogenic peptide cause nuclear fluorescence in ICC?

Hi all, I am validating a polyclonal antibody raised against human ANT4, through WB and ICC. In most of my controls, the antibody shows very little off-target binding, but when I pre-incubate the...

03 March 2021 5,999 3 View

What is the status of bread making and more bakery foods with the use of insect flour/powder?

Insects have been consumed by human diet since prehistoric times. At present, the idea of looking at insects as food has been getting traction worldwide, also in response to increasing food...

03 March 2021 6,223 5 View

Does Napabucasin soluble in dichloromethane and in ethanol?

I need to prepare a solution of Napabucasin (inhibitor of cancer cell stemness) in dichloromethane. The drug is expensive, so maybe somebody already tried to do it. If it is soluble, what is the...

02 March 2021 9,945 3 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

Help request in CST microwave?

im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...

02 March 2021 2,246 2 View

Discrete Phase model (DPM) particle break-up has particle size limits during particle tracking?

Hello, I am currently working on simulating water droplet partciles in a closed room. When I use uniform particles, without "particle break-up", I can carry out the simulation without any problem....

02 March 2021 3,053 2 View

How optimize the Size Exclusion Chromatography?

Hello! I'll do a size exclusion chromatography, but I only have an open column, and I'll perform the peptide extraction from yeast, using buffer lysis (sodium phosphate 50 mM/NaCl 30 mM/DNAse and...

01 March 2021 2,215 2 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

No title

01 March 2021 3,905 5 View