Do you have this Report (Pacific Earthquake Engineering Research Center); no. PEER-98/01.
"Seismic performance of well-confined concrete bridge columns".
Dawn E. Lehman and Jack P. Moehle.
Thank you four your help
Dear Hayet:
Please go to the following web-page to order a printed copy:
https://peer.berkeley.edu/node/59/
Sincerely,
Arturo
Thank you very much Arturo E Schultz for your help.
Dear Friends,
I have the honor to share with you the relevant report by Dawn E. Lehman and Jack P. Moehle entitled 'Seismic Performance of Well-Confined Concrete Bridge Columns'.
https://drive.google.com/file/d/1v1ZoI9TUkQqk5VTDjRB_TDO58nRYupJK/view?usp=sharing
Good reading
Dear colleagues, To evaluate the OpenSees capabilities for shear-flexion interaction. What is the best way to use. Rotation based shear failure model (RotationShearCurve) with...
09 October 2019 5,780 3 View
Hi; I am s PhD student in Earthquake Engineering. Now, I work on the development of seismic fragility curves for bridge piers. For this, I use IDA method by using OpenSees tool. For this, I...
10 November 2018 9,090 4 View
Hi, Please, can you help me on the method of plotting fragility curves from regression analysis of column or PSDM (Ln (Drift) Vs Ln (PGA)) I am very grateful for your help. Cordially.
10 November 2018 9,388 6 View
Hi everyone, I'm modelling a cantilever column in 2D with a section (1.0x 14.25m) as nonlinearBeamColumn element and i used zerolength section element to simulate the effect of reinforcement...
08 September 2018 2,592 0 View
Please, do you have this thesis, 'Performance modeling strategies for modern reinforced concrete bridge columns'. Thesis (Ph.D.) - University of Washington, 2006 by Michael Berry.
01 January 1970 3,035 2 View
A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...
11 August 2024 9,801 2 View
Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...
11 August 2024 8,141 3 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
I have already collected seismic data and need to analyse them. Please assist with the software that can also analyse the Peak Ground ACCERATION (PGA).
10 August 2024 4,839 0 View
Who will bear moral responsibility for the deaths of thousands of people in the event of an earthquake? Weeks and months remain before the onset of strong earthquakes that bring death to...
08 August 2024 6,134 12 View
I've been performing RNA extraction on cotton petiole tissue for a few months now using the method described in the following paper, a derivative of the typical hot borate method...
08 August 2024 9,882 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I'm working on selecting antibodies against a recombinant protein that has a His-tag. My idea is to first bind the recombinant protein to a HisTRAP column and then use this column for an affinity...
07 August 2024 505 3 View
I am trying to recover liquid CO2 from a mixture of 0.6 CO2, 0.3 N2, and 0.1 O2. My aim is to recover about 99% liquid CO2 at the bottom of the column and make sure the amount of gaseous CO2...
06 August 2024 4,611 0 View