I want to buy some materials , ie Al A356 and TiC. Can anyone recommend an address of a site that I can refer to for prices?
If you are in Iran, You can tell with this
021-33957567
Email :[email protected]
201-Saadi commercial center- Saadi street - Tehran -Iran
I tried some etch reagents like Keller, weck and HF but I couldn't see the grain boundaries of Al matrix.
07 August 2017 2,903 2 View
ABS = Acrylonitrile Butadiene Styrene PLA = Poly Lactic Acid these materials are used in 3D printer. the final part is combining of two materials that are mentioned before. I want to destroy PLA...
01 February 2015 5,178 7 View
I studied some articles and in some images the color of Al2O3 particles in Al matrix composite is white but in my image of SEM ( with EDX) is gray. Can anyone explain the difference?
06 July 2014 8,286 21 View
Al2O3 particles don't have wettability with molten Al. They float on the surface of the molten without any change in structure of particles.
31 December 2013 5,147 7 View
I want to know that i can do heat treatment Al2O3 particles ( 900 deg for 2 hrs ) without inert gas ? because i don't have this instruments for inert gas in the furnace.
31 December 2013 4,200 6 View
I'm working on MMCs with Al2O3 reinforcing particles in Al matrix. In articles it is mentioned that for better wettability of Al2O3 with molten Al it's effective to add Mg powder. How can I avoid...
31 December 2013 456 1 View
Al A356
31 December 2013 7,407 2 View
I did several experiments for dispersion of Al2O3 particles in molten Al A356 matrix but I couldn't catch any results, heat treatment of Al2O3 in 900 deg for 2 hrs and another experiment in 400...
31 December 2013 6,932 5 View
According to articles I've added 5 percent alumina to molten (aluminum) but the amount of dissolution were low and it were exposed a lot of powders on the surface of the molten. I can't...
11 December 2013 615 8 View
I've tried more than once but I can't install that. Does anyone have an idea why this keep happening?
10 November 2013 7,213 8 View
Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...
10 August 2024 6,493 1 View
What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?
29 July 2024 7,714 4 View
In some data sources it has been grouped in Q1 and some shows it is Q2.
29 July 2024 4,227 2 View
Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...
28 July 2024 5,771 2 View
Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?
27 July 2024 648 3 View
// interested in the difference between floating events and short circuits.
22 July 2024 6,565 0 View
I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...
22 July 2024 3,490 2 View
Chemical Engineering /Food Engineering
20 July 2024 4,152 4 View
I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...
16 July 2024 3,212 5 View
I want to reduce simulation time in CST for frequency domain solver by upgrading my computer. I already have discrete GPU but it doesn't seem to make any difference at all compared to integreted...
10 July 2024 2,789 4 View