P-E hysteresis generate for ferroelectric ceramic?

19 April 2022 0 2K Report

Has anyone built a sawyer tower circuit and produced a P-E hysteresis curve in parallel plate ferroelectric ceramics (for example 1mm in height 10mm in dimensions with Ag paste applied two surface)? Could you share with me information about this hardware? I would like to see the installed mechanism and get information about it rather than the map of the circuits. Thanks in advance for your interest...

Badges
Science topic

Similar topics
Journal Impact Factor

More Ugur Sen's questions See All

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Hello fellow researcher .. What is the meaning of your name?

I would like to create a small guide containing the meanings of the names .. Thanks to everyone who cooperates with me in achieving it.

03 March 2021 5,266 4 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

Does anyone know HRM channel in a 2 plex QIAGEN Rotor- Gene Q qPCR can be used as a separate channel?

I am going to have 3 different probes in my qPCR work that I am going to do. But I realized that the machine we have in the lab is a Rotor-Gene Q 2plex HRM Platform, saying it has green, yellow,...

01 March 2021 8,544 1 View

Adherance of Polyaniline coating over stainless steel?

Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...

01 March 2021 8,220 2 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View

No title

Does anyone have the experience of using Taq Man probes in the QIAGEN Rotar- Gene qPCR machine?

01 March 2021 5,311 1 View

Why is the sum of the elements in a row in a Q matrix equal to zero?

When explaining substitution models, the substitutions are expressed as Q matrix. Why is the sum of the elements in a row zero?

28 February 2021 3,864 3 View

How to model the battery pack in PSIM or PSCAD?

Hello, I have simulated a single battery cell using Thevenin equivalent circuit. For a battery pack, I have a large number of cells connected in series and parallel connections. Is there any way...

28 February 2021 2,116 1 View

What is difference between In-line transmission (%) and Total transmission (%) value of optically transparent Ceramics?

I am working on transparent/translucent zirconia-based ceramics. In many papers, I have seen that they are reporting both In-line transmission (%) & Total transmission (%) value of...

20 February 2021 9,405 6 View

How to get better phase shift in C-V curves for ferroelectric devices?

I tried to sweep my ferroelectric devices from -2V to 2V and then from 2V to -2V and The two hysteresis peaks are off by several microFarads. Should i increase bias voltage? I am doing these...

16 February 2021 8,514 2 View

What is the general cyclic energy degradation factor for plain concrete at material level in stress strain curve?

Plain Concrete subjected to cyclic loading get reduction in its stiffness and strength with the every cycle of loading. What is ratio of energy enclosed in one hysteresis loop to adjacent...

10 February 2021 1,051 1 View

Using liquids as superstrate in Fabry-Perot Cavity Antenna?

Hi, A Fabry Perot Cavity allows to increase the directivity of a low gain antenna by putting in the top of cavity a superstrate with high permittivity such as a ceramic (er=10.2). However,...

09 February 2021 6,799 8 View

Sample preparation for ceramics i.e. iron silicate (fayalite), iron oxides, alumina, spinel mineral (hercynite)?

Recommendations in preparing ceramics for nanoindentation and in the process minimize introducing stresses from sample preparation i.e. polishing stage.

02 February 2021 6,211 3 View

What should I do if the reviewer couldn't finalize the review in the journal's given time?

I have Submitted 2,3 Papers in Science Direct associated Journals but the time of the first decision has been ended so What should I do? Could I email them to remind them about the first decision?

01 February 2021 5,788 7 View

What are the thermodynamic and kinetic similarities and differences among dendrite formation during solidification of metals, ceramics and polymers?

Basic dendrite formation of metallic alloys are explained by thermal and constitutional degree of supercooling and most-supercooled band of liquid somewhat ahead of solidification front that...

30 January 2021 8,450 2 View

Control in microstructure with growth inhibitor?

Dear researchers, I wish to understand the role of grain growth inhibitor in controlling the microstructure of the ceramic pellet. How it controls the growth? Also, I wish to know the grain...

15 January 2021 3,859 3 View

How can I select the concentration of test sample for MTT assay?

I synthesize a powder composite include two ceramics and a polymer coating. I want to do MTT test and I'm not sure about the concentration of powder dissolve in DMEM media. Shall I start with a...

10 January 2021 9,984 1 View

Can you please help with the problem modeling a damper in ABAQUS?

Hello everyone, I am trying to model a damper in ABAQUS. I have obtained hyperelastic properties using a uniaxial tensile test and viscoelastic properties by relaxation test conducted in the...

09 January 2021 4,515 1 View