OOMMF - FAQS.TIPS

12 December 2016 1 3K Report

How could I simulate first order reversal curves of a nanowire?

M. Ghaffari

https://math.nist.gov/~MDonahue/pubs/nanowires-20100927.pdf

https://nanohub.org/resources/23356/download/Simplified_Generation_of_Input_Models_for_the_Object_Oriented_MicroMagnetic_Framework.pdf

https://www.physnet.uni-hamburg.de/services/biblio/dissertation/dissfbPhysik/___Volltexte/Theo___Gerhardt/Theo___Gerhardt.pdf

https://aip.scitation.org/doi/abs/10.1063/1.2829817?journalCode=jap

https://www.zurich.ibm.com/st/nanomagnetism/spintevolve.html

https://repository.kaust.edu.sa/bitstream/handle/10754/582600/manuscript.pdf?sequence=1&isAllowed=y

http://digitalcommons.unl.edu/cgi/viewcontent.cgi?article=1037&context=cmrafacpub

Badges
Science topic

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View

Should I use Pressure Based Solver or a Density-Based Solver?

Dear researchers, I want to simulate a flow (air) in a wind tunnel, and I want to integrate a fluidic actuator inside it in order to control the separation of the boundary layer. At the blower...

22 February 2021 4,882 3 View

How to simulate 5G Quality of Service characteristics?

For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...

21 February 2021 7,624 3 View

Open Source IoT Simulators supported by Machine Learning?

Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...

21 February 2021 2,333 4 View

How can I simulate the optical absorption spectrum of a biomaterial (like DNA or protein) in COMSOL?

I need to simulate the optical properties of a biomaterial, namely DNA, in COMSOL. Basically I need to simulate the IR absorption spectrum of a cylinder filled with a 'concentration' of DNA. I am...

21 February 2021 3,043 3 View