Is it possible to measure the available power/energy on a distribution line at any point on the line before getting to the consumer premise meter?

Let us assume a 33/0.415kV or a 11/0.415kV transformer is metered at a distribution substation. There are N number of houses connected to transformer. The houses are located at distances 1

29 February 2020 7,925 3 View

Decrease in FT-IR intensity (absorbance) of polymer reinforced with MMT/CNT concentration?

Dear All, Please what could have caused the peak intensity of polymer reinforced with pristine CNT and modified MMT (CNT/MMT hybrid) to be reducing with increase in the nanohybrid filler...

30 January 2020 6,752 6 View

Measuring the electrical conductivity of Polymer/CNT nanocomposite?

How can I determine electrical resistivity or conductivity of polymer nanocomposite? Several attempts using current or voltage generator has proved abortive as all samples reading same value with...

24 January 2020 9,464 3 View

What is the impact of scientific conference on development?

Development refers to a process of growth which is engendered by research. But there are different ways of reporting results of research activities asides scientific conference. Results could be...

16 October 2018 7,612 3 View

How can I reduce noise on the cyclic voltammogram during measurement?

Hello scholars, Recently, I have been working on AOR. I have obtained interesting results, however, the result is a bit disturbing as it comes with noise in the curve. Below is a picture of such....

17 August 2018 4,827 18 View

How can I specify "CONC" as initial condition for a stress analysis in a concrete section in abaqus

24 April 2017 7,896 2 View

What is the cheapest and easiest way to measure heavy metal and nanoparticles in air samples?

As a means of risk assessment in home or work places, a measurement of dust concentration could give a lot for public health concern, therefore quantifying these contaminants become an easy way to...

28 February 2014 1,139 2 View

For those of us in chemistry, environmental science, civil engineering, industrial chemistry, analytical chemistry, chemical engineering, biotech

For those of us in chemistry, environmental science, civil engineering, industrial chemistry, analytical chemistry, chemical engineering, biotechnology etc this paper might be helpful. Link is...

01 January 1970 9,300 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Where to find data on trees in tropical agroforestry?

Hi, I'm looking for data (mainly related to management: growth rate, canopy size, soil and climate preferences, etc.) about tropical trees used in tropical agroforestry. Have you ever heard about...

28 February 2021 7,356 8 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

Have you ever experiencing air vent trouble in fermentation process?

Dear all, My research group is currently working with a 12-litre fermenter. Somehow, if we do the fermentation for more than 20 hours, the process will be more prone to contamination. Our current...

23 February 2021 1,908 2 View

Help with assigning pressure boundary conditions in FLUENT on a large structure?

Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....

22 February 2021 9,972 4 View

What type of pressure sensor are usually used in microfluidics?

My team is designing a dual channel microfluidic chip that runs air and water. I think we've decided on the NE1000 syringe pump for it's versatility and feedback control. We will be ordering the...

18 February 2021 9,928 2 View

Not able to charge-discharge Li-ion coin cell at higher C rate ?

I am working on cathode material. I have made different Li-ion coin cell against Li metal using commercial available cathode materials such as LCO,LMO, LFP and NMC and also with the lab...

18 February 2021 1,450 3 View

How to find the air side pressure drop in a spiral fin tube bundle cross flow heat exchanger?

How to find the air side pressure drop in a spiral fin cross flow heat exchanger? The pressure difference at the inlet and outlet is very low compared to the experimental results, which I...

18 February 2021 1,109 2 View