Submitting to arxiv before submitting to a journal?

Hello, everyone! Just wanted to know if I can first submit my paper to arxiv before I submit to a journal in elsevier. Hoping to find a clear answer. Thank you!

12 January 2021 5,266 3 View

What crossover operators can be used for a GA that finds suboptimal positions for a set of buildings?

I'm currently working on my undergraduate thesis where I develop a genetic algorithm that finds suboptimal 2D positions for a set of buildings. The solution representation is a vector of real...

11 January 2021 9,835 4 View

How does one subset time series GPS data to to 1 hour intervals?

I have time series GPS tracking data from a number of individuals, all with varying time between locations (i.e. certain individuals recording at 15 minutes intervals, others at 20 minutes or 1...

06 December 2020 9,038 3 View

Popular image segmentation quality measures ?

Evaluation metric to assess superpixel based algorithms

13 September 2020 5,793 13 View

What is the best research topic related to Disaster Management for Senior High School Students?

Disaster, Youth, Research Topic

07 September 2020 8,789 9 View

Can I ask for your suggestions in freeze-drying PCR/LAMP mixes?

We have a project on development of a dry loop mediated isothermal amplification (LAMP)-based kit for detection of plant viruses on field site. One of the challenges in this project is the...

06 September 2020 8,531 4 View

How much is a paper publication in IEEE non-open journal?

Hello, I was wondering how much it cost to publish in an IEEE journal that is non-open access. Is there a direct answer to this? If also, can anyone suggest a good journal with a decent Impact...

15 July 2020 2,885 8 View

CNN papers using Random Search Algorithms?

Hi, I'am looking for good papers that applied Random Search to optimize their hyper-parameters for CNN. Thank you!

09 March 2020 2,097 3 View

How to edit the single phase UDF for a multiphase case?

In the first case (single phase case) liquid enters the tube and absorbs heat energy which is produced by the solid region. There is no phase change happening here. The following UDF is used to...

07 January 2020 5,829 1 View

Can anyone give me some tips in publishing my research in Scopus indexed journals?

Looking for ways to how I can somehow get my work published on Scopus indexed journals? Here are some of my works. I'm planning to conduct new experiments and improve my writing. I want to...

17 December 2019 713 6 View

How climate change will influences human and animal behavioral change?

The role of climate change influencing the human behavior as well as economics interest

01 June 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is Flat Lens Antenna?

28 February 2021 5,433 3 View

Can impedance of antenna be less than 50 ohms?

I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...

27 February 2021 4,218 7 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

How to measure angle between laser travel path and machine axis in Laser Measurement system?

25 February 2021 1,987 3 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

Have you ever experiencing air vent trouble in fermentation process?

Dear all, My research group is currently working with a 12-litre fermenter. Somehow, if we do the fermentation for more than 20 hours, the process will be more prone to contamination. Our current...

23 February 2021 1,908 2 View

Help with assigning pressure boundary conditions in FLUENT on a large structure?

Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....

22 February 2021 9,972 4 View

Helix antenna coupling problem?

Dealing with a helix antenna, made with flexible material and not rigid like using a PCB board or wire. At the beginning of the helix is too close to the ground plane, causing coupling. How can I...

21 February 2021 4,453 3 View