Mems fabrication facilities required for research work in India - can anyone help?

More Vishal Vasistha's questions See All

Need assistance in solution convergence and temperature contour confirmation using non-premixed combustion model with in ansys fluent software?

I am simulating temperature results in ansys fluent CFD software using diesel-air mixture. I have used non-premixed combustion model with chemkin mechanism. I am not able to get conversed solution...

03 April 2018 752 3 View

May I know advantages and disadvantages of using aluminium oxide nano powder over other nano particles in diesel blended fuels?

31 December 2017 3,087 0 View

Can nano-particles be used in fuel properties table in Diesel-RK software for simulation?

I am planning to prepare fuel blends with nano-particles addition in my project. Is it possible to simulate engine performance by adding nano-particles in fuel blends using Diesel-RK engine...

07 August 2017 924 0 View

I need support for engine simulation on Diesel-RK software. Please Let me know if someone can do!

I am getting difficulty to shown simulation results on Diesel-RK software. I am attaching here the image showing error in displaying results. I am trying for remote access of this software on my...

07 August 2017 6,608 4 View

Can GT-Suite simulation software be used to check performance of diesel engine fueled with blend of diesel,water and ethanol?

01 February 2017 2,883 0 View

Can anyone arrange the AVL Boost software free of cost?

Can anyone arrange the AVL Boost software free of cost? Do you have any link, from where I can download its free version. I need it urgent for my project work but not able to purchase due to its...

31 December 2016 7,822 0 View

May I know is there any vehicle running on liquid injection LPG fuel in India?

31 December 2016 492 0 View

May i know which is less costly - to make synthesis of nano material self or purchase nano metal powder directly from market?

10 November 2016 2,228 6 View

As ethanol has low cetane number, low calorific value, increase NOx, increase ignition delay than why widely used for research purpose with diesel?

09 October 2016 6,456 7 View

Can any one provide me some research papers based on water-diesel -ethanol emulsions?

CAN ANY ONE PROVIDE ME SOME RESEARCH PAPERS BASED ON WATER-DIESEL-ETHANOL EMULSION?

09 October 2016 7,198 0 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Can't spin-orbit coupling(SOC) be included in optical properties calculation in CASTEP?

I am currently using CASTEP version 2020. When I want to run optical properties calculations with spin-orbit coupling(SOC), I encounter the following error in a pop-up window before the job gets...

02 August 2024 2,890 0 View

A Question about Phd thesis?

Hello everyone What is your opinion about the introduction of an expert decision support system in which the rules are extracted from existing data without human intervention, instead of being...

31 July 2024 5,785 4 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

After a lot of feature engineering for CTR modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing?

After a lot of feature engineering for click-through rate modeling, it feels like it's basically the end of iteration? I mean, it's not cost-effective to keep doing it?

29 July 2024 4,955 0 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

What topic or subject does Production Engineering need to address more?

Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?

27 July 2024 648 3 View

Harsha Sanjeev

Try Indian Institute of Science, bangalore and IIT - Bombay, Mumbai

Vishal Vasistha

thanks Mr. Harsha.

Sumathi Ayyalusamy

IIT-Bombay..and get scheduled for the duration.

Jagadesh Babu Nakka

I am interested to do research work in mems devices but don't know where to get fabrication facilities. Can someone suggest resources for this in India?

Mems fabrication facilities required for research work in India - can anyone help? - ResearchGate. Available from: https://www.researchgate.net/post/Mems_fabrication_facilities_required_for_research_work_in_India-can_anyone_help [accessed Dec 21, 2015].

Jaising Pednekar

IITB, IISc has good MEMS facility. SITAR Bangalore has professional MEMS fab.

Some of the DRDO labs have MEMS facility , try to contact SSPL Delhi, RCI Hyderabad, R&DE(Engrs) Pune or NPOL Kochi

Neelima S

CeNSE-Center for NanoScience and Engineering of IISc Banglore has MEMS fabrication and chracterization facilities along with packaging.