May I do EIS and electrochemical noise and Tafel together on one substrate?

11 November 2017 0 8K Report

may I do Tafel, Electrochemical Impedance Spectroscopy(EIS) and Electrochemical Noise(EN) tests on one substrate? if yes can you explain about sequences.

for example we can have EIS then Tafel. so if it is possible, I want to know when can I do EN test? along with EIS or etc.

thanks

Badges
Science topic

Similar topics
Chemistry
Electrochemistry

More Mohamad Ali Farzaneh's questions See All

Can we Using Linear Polarization Resistance method after Wheel Test?

According to Nace 1D182 for evaluating of film-persistent corrosion inhibitors for oilfield applications we can using Wheel test method. moreover, we can use Linear Polarization Resistance(LPR)...

09 October 2017 2,521 6 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

What do I do with DLS peaks that are from the buffer?

I'm looking at the aggregation of my protein sample using DLS. Unfortunately, my buffer (20mM HEPES) also results in a set of peaks. These are at approximately 1 and 1000 d.nm. The lowest peak...

01 March 2021 9,015 2 View

What is the indication of the absence of peaks in Methanol electrooxidation CV curves ?

I have several question regarding the MOR; hope anyone help me better understand. 1- in CV using (KOH+MEOH) what is the indication of absence of the redox peaks? shouldn't they exist as a sign...

28 February 2021 4,851 8 View

Why initial concentration of Pb not the same as calculated one when testing using AAS?

I am currently doing research on the adsorption of heavy metal using magnetic reduce graphene oxide. I use AAS to determine the concentration of the heavy metal. I prepare the Pb solution with...

26 February 2021 9,580 4 View

Is this the write procedure for acid digestion of soil for heavy metal analysis using AAS?

How to do acid digestion of soil sample with 3:1 aquaregia in an open vessel?

23 February 2021 3,053 7 View

Have anyone checked before Cyclic voltammograms of intial ITO substrate and E-teck?

As a beginner in electrochemistry, I tried to obtain cyclic voltamograms of commercial anatase powder deposited on an ITO substrate or on Eteck. After several attempts, I noticed that my cyclic...

23 February 2021 3,175 3 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

What low-cut filter (high Pass frequency) to be used for response spectrum (Tripartite plots) ?

What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...

21 February 2021 9,273 2 View

Is that possible to do an impedance measurement without FRA module?

One of my colleagues said, "the impedance you can measure with the three electrodes and with the specific sequence varying the frequency" Is it possible to configure the potenciostat without the...

21 February 2021 418 2 View

How can I simulate the optical absorption spectrum of a biomaterial (like DNA or protein) in COMSOL?

I need to simulate the optical properties of a biomaterial, namely DNA, in COMSOL. Basically I need to simulate the IR absorption spectrum of a cylinder filled with a 'concentration' of DNA. I am...

21 February 2021 3,043 3 View