Masslynx - duplicate/wrong retention times.

01 January 2017 0 2K Report

Recently I was examining a sample quantification report produced by MassLynx 4.1 software (I'm attaching a picture of it). One thing bothers me concerning this report. Why MassLynx sometimes duplicates peak's retention times? Is it a bug or feature? I'm not using MassLynx for my everyday work so I'm asking more experienced users.

With my best regards

Andrzej

Badges
Science topic

More Andrzej Wasik's questions See All

Which internal standard? Deuterated or C13 enriched?

I'd like to hear your opinion concerning internal standard choice for steroid analyses. There are two kinds of IS available, those labelled with deuterium and those labelled with carbon-13. My...

02 March 2013 4,664 25 View

How two melting peaks in DSC of polypropylene can be merged into one crystallization peak?

The figure shows DSC cooling (blue) and 2nd heating (green) curves (step: 10 K/min) for a commercial sample supplied as Atactic Polypropylene (APP). The heating curve illustrates two major...

03 March 2021 5,857 3 View

How to quantitative analize the data of TNBS assay for gelatin?

Estemeed colleagues, I found some issues regarding the quantification of the data for TNBS assay. There are different protocols on how to perform that but it is clear to me the "fil rouge" that...

02 March 2021 2,616 1 View

Issues with Permeabilization during Flow Cytometry?

Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...

01 March 2021 3,867 3 View

How to accurately quantify chitin?

Hi all, I have been working on the quantification of chitin in insect samples and feed for a while but I can notice that the quantification methods (e.g. exposure to HCl, NaOH, and weighing sample...

01 March 2021 1,843 2 View

What do I do with DLS peaks that are from the buffer?

I'm looking at the aggregation of my protein sample using DLS. Unfortunately, my buffer (20mM HEPES) also results in a set of peaks. These are at approximately 1 and 1000 d.nm. The lowest peak...

01 March 2021 9,015 2 View

Mediation path analysis - Can I run two seperate models?

I am wanting to run a serial mediation model with 2 x IVs, 2 x MVs, and 3 DPs (all continuous). Is it problematic to run 2 different models for each IV, keeping the MVs and DPs the same in each...

27 February 2021 5,681 3 View

What information can be had from raman at higher wavenumber?

i have recorded raman spectra of strontium oxide thin film. the spectra were recorded in the range 400 to 4000 cm-1. i have reference to peaks upto 1000cm-1. but i couldn't find literature for...

26 February 2021 2,499 1 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

How can I find a Raman spectrum wavenumber corresponding to what compound?

I have several Raman spectra with very distinct peaks at certain wavenumbers, such as 277, 359, 466, 583, 623, 686, and 795cm-1. How can I identify them to what compound(s)? The RRUFF and others...

24 February 2021 363 3 View

Do you kow of any database containing data on retention time, log P and polarizability for a large number of molecules?

Hi, I am a chemistry undergraduate doing my dissertation project on HPLC. In my project, I need to predict the HPLC retention time of 20 aromatic molecules, the calibration set. To do this I will...

24 February 2021 2,602 1 View