Macrophage differentiation/polarization on uncoated glass coverslips

More Andreas H Wagner's questions See All

Can you suggest a stable miRNA control in human endothelial cells (HUVEC) which is not influenced by cytokines?

We already tried RNU6-2 but failed .... any suggestions? Thank you!

08 September 2014 5,426 6 View

What is a good marker to distinguish between bladder urothelial cell and smooth muscle cells using PCR analysis?

We separated the urothelium by stripping and now want to show that there are no smooth muscle cells left in the urothelial cells preparation and vice versa. For smooth musle cells I will use...

03 April 2013 8,355 14 View

I am looking for a suitable immunoprecipitation antibody for TRAF6 in human cells. Any suggestions?

I would like to use protein G dynabeads.

09 October 2012 1,497 3 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Issues with Permeabilization during Flow Cytometry?

Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...

01 March 2021 3,867 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

What could be some reasons why unstimulated monocytes are getting activated?

Im doing PBMC isolation -> CD14+ enrichment using magnetic beads -> stimulation setup. My negative control is just cells in cRPMI but they seem to get activated over and over again.

28 February 2021 7,883 3 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

Looking for advices and tips to improve the staining and the gating strategy in human blood?

Hi, I am staining a human blood with CD19, CD3,CD14 and CD16. My gating strategy in FlowJo goes like this: - First, I gate a general population SSC-A VS FSC-A => Then gate for single cells, =>...

21 February 2021 5,724 4 View

How can I measure the surface interaction or surface interfacial chemistry between polishing abrasives and upper surface of substrate ?

I am working on polishing abrasives. I need to do few characterizations ? which can provide the on time surface chemistry of substrate with polishing abrasive during optical polishing. I would...

18 February 2021 5,319 3 View