I'm searching for a lab abroad where I can visit for a few months to carry out my research work.

Obinna Ofoegbu @Obinna_Ofoegbu

08 August 2013 0 2K Report

I'm working on molecularly imprinted polymer material. Equipment and environment are challenges.

Badges
Science topic

More Obinna Ofoegbu's questions See All

Can this chemistry feasibly occur H2+O3?

H2O2 exists and H2O is part of us.

09 October 2014 467 2 View

What is the simplest method of selecting functional monomer and other parameters for molecular imprinting?

Template characteristics affects molecularly imprinted polymer characteristics if careful selection of reaction components is not done.

09 October 2014 3,986 2 View

What is the advantage of rotavap over conventional distillation systems?

What effects does the technique have on active extracts?

02 March 2014 1,945 2 View

How relevant is statistical analysis to contemporary product-targeted Research and Development?

To what degree does the acceptance and application of a research output depend on statistical evaluations from packages like ANOVA and the rest?

11 December 2013 7,988 1 View

Are your sources from wild tubers or Rhizomes and what are the folk tales of the indigenous uses of these raw materials?

Most of the so named wild species have medicinal applications based on their compositions. Using the term "wild", may not be appropriate rather "non-edible" may be better suited.

01 January 1970 5,792 5 View

How will I organize the raw data that I have from a QCM analysis to interpret the outcome of my molecularly imprinted polymerization reaction?

Your toughest technical questions will likely get answered within 48 hours on ResearchGate, the professional network for scientists.

01 January 1970 5,657 0 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

Inquiry on Maximum Nucleic Acid Volume for 2.5 mL Liposome Solution?

I am currently working on a project involving liposomes and need to determine the maximum volume of siRNA that can be added to a 2.5 mL liposome solution with a total lipid concentration of 10...

30 July 2024 6,420 1 View

How can I use DFT-D3 correction ( Siesta version 5.0.1)?

Dear Siesta Users, I installed Siesta 5.0.1 and I want to use Grimme's D3 correction. According to the 5.0.1 manual, I could use a few parameters to include the D3 correction in the...

27 July 2024 5,748 0 View

EDC carbodiimide and NHS easter 's half life among different pH?

It has been long known that EDC carbodiimide and NHS easter's half life agains hydrolysis are highly related to pH. However, very surprisingly, not yet found a paper giving a table/chart of their...

25 July 2024 8,738 0 View

Mechanochemistry: ball to powder mass or ball to powder volume?

I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...

23 July 2024 9,938 1 View

How to eliminate the carry-over effect in GC-MS/MS system?

Hi, I am a PhD student working at Jagiellonian University, Faculty of Chemistry. My work is related to the development of new analytical methods for the quantification of short-chain fatty acids...

22 July 2024 5,492 6 View

Is it possible to manufacture polypropylene sheets using a biaxial process?

I know that films and other low-thickness laminated products are produced using biaxial orientation, but is there something similar for sheets with a thickness of around 6 mm? Or are they...

21 July 2024 1,559 1 View

MDCI module in Orca software?

Dear Researchers, My question is associated with the "MDCI" method in Orca. Please let me clarify my question using a simple example: Suppose we are going to perform CBS extrapolation using "!...

21 July 2024 1,632 0 View

Why am I seeing only one initial maximum in torque-time curves for the fusion of PVC in a Brabender?

We're studying the stability and fusion behavior of multiple PVC compounds in a Brabender. After a few trials, we set the temperature at 195 °C and the rotor speed at 70 rpm. Samples differ in...

12 July 2024 2,768 1 View

What are the principles of physical chemistry?

what are the main points

10 July 2024 9,236 5 View