A question regarding Response factor in GC. what does area count mean?

i was reading about response factors in GC and i encountered the term area count, I was wondering if anyone can explain it to me, i have a general idea about the meaning but i'm not sure. does...

30 March 2020 7,854 1 View

Which software is best for estimating of pipeline corrosion rate?

I want to calculate Steel pipeline corrosion rate in different conditions, so Which software is best for estimating of pipeline corrosion rate?

03 March 2020 1,779 4 View

EEG connectivity calculation via HERMES toolbox ?

Hello everyone I am currently trying to calculate phase lock value for my EEG data with the help of the HERMES toolbox in Matlab. I have a total of 48 subjects with different channel location...

04 January 2020 5,220 1 View

How to evaluate the Antibiofilm effects of nanoparticles against Candida Albicans ?

how to evaluate the Antibiofilm effects of nanoparticles against Candida Albicans with an efficient and simple method?

09 October 2019 3,470 3 View

How can one simulate agglomerated cork in ansys and which engineering model can provide the better results?

I'm going to simulate the structural response of a sandwich structure with agglomerated cork core under bending and compression loading. Is there any reliable information about the structural...

28 August 2019 2,843 2 View

What are the reasons for Infertile and empty' seeds in the Cuminum cyminum L?

what are the reasons for Infertile and empty' seeds in the Cuminum cyminum L?

24 June 2019 8,648 2 View

Hi.I have an extruder for dewatering a two phase fluid. I want to setup slip condotion in wall boundary condition in Ansys Fluent. how can I do that?

in wall boundary dial box I should specify the shear stress in three direction (x,y,z). how can I measure this shear stress? please help me....

10 June 2019 7,550 1 View

What are the best polynomial approximation functions for analyzing free vibration and impact analysis of plates?

I want to do a free vibration analysis for a plate. In this research, I want to use the Ritz method. For Ritz-shape functions, which are the best polynomial functions that give the most accurate...

10 April 2019 2,612 5 View

Can I still publish a paper if there is something rather similar in a patent?

I've tested a variety of reagents for the synthesis of a compound and found one that has never been used before and yields a good product. after my experiments i did some research and came across...

04 September 2018 5,726 3 View

What does a higher (or lower) soil sorptivity indicate?

sorptivity is defined as the capacity of soil to absorb or desorb water by capillarity. but what does higher sorptivity mean? does it mean the part of infiltartion that depends on capillarity...

30 July 2018 4,467 4 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View