Is there any utility program (code) which estimates the effective resistance of a graph?

29 January 2019 0 4K Report

As computing the exact pair-wise effective resistance of a graph is computationally expensive, therefore I am looking for a utility program (can be in any programming language) which estimates the effective resistance of a graph efficiently. Any help will be appreciated.

Badges
Science topic

Similar topics
Mathematical Sciences
Graphs

More Anwar Said's questions See All

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View

Any information about dinitrosalisylic acid reagent end point color stability ?

I work on estimation of alpha amylase activity using dinitrosalisylic acid reagent If i put the reagent to stope the enzymatic reaction and allow the reagent to react with the produced reducing...

17 February 2021 7,402 4 View

Can any one explain why the ethyl ester Biodiesel (FAEE) has higher than that of the metyl ester FAME- both of them are derived from the same oil?

Biodiesels derived from waste vegetable oil transesterification with Ethanol (FAEE) show higher peroxide values than those derived by transesterification with methanol (FAME) prepared under the...

13 February 2021 193 6 View

What is impact of sampling frequency on deep learning?

Greetings, everyone. I am a bit curious to know how the sampling frequency of the device that captures the physiological signals impact the deep learning process. For example, if a device abc...

03 February 2021 379 4 View

Why sometimes current- voltage plot in chemiresistors/ FET does not pass through the origin?

I am trying to measure resistance from I-V curve from a chemiresistor/ FET sensor with a keithly sourcemeter. The substrate is soaked/ wet with protein and phosphate buffer only. But the I-V line...

24 January 2021 8,009 3 View

How to interact with internal memory of FPGA and connect it a signal or array inside a module?

I am trying to implement a processor tile on FPGA using vivado but it is taking too long to synthesize design due to large amount of Instruction and Data Memory. Currently, I have put complete...

05 January 2021 8,349 1 View

Is the globalization concept under threat by the effect of Covid-19?

Is the globalization concept under threat by the effect of Covid-19? Because Nobody knows how long the COVID-19 epidemic will last. People around the world may have to wait until a vaccine is...

02 January 2021 8,155 1 View

Upto how much %age of phase can be visible as peak in XRD?

When we do XRD analysis, high intensity peaks are obtained. But there are some very small peaks too which seem to be negligible. Some phases are confirmed from SAED pattern on the basis of...

01 January 2021 3,727 2 View

If i want to use annual time series data, but the number of observations are less then requirement, so i can convert data in quarters?

27 December 2020 7,304 19 View

Log 10 transformation versus Benforrini correction?

We have conducted a study to compare the effects of 3 training methods on body composition and cardiovascular risk factors. A Log 10 transformation was applied for all non-normal distributions,...

10 December 2020 877 5 View

What is your perception on using visual analysis or quantitative approaches to evaluate data from single-case research designs (n of 1 trials)?

Results of single-case research designs (i.e., n-of-1 trials) are often evaluated by visually inspecting the time-series graph and computing quantitative indices. A question our research team is...

03 March 2021 687 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How do you write a simplified C block code of this average-current control on PSIM?

This is a Buck (step-down) Converter and I am new to this program. I need to program with simplified C block and I actually don't know what to do. Can anyone show me how to do this? Or at least...

02 March 2021 8,233 1 View

Do you know good and user-friendly programs to measure plant quantitative traits?

For my research i will need to measure plant quantitative traits (especially leaves area and roots length, but would be nice to add some more information). I recently discovered...

01 March 2021 5,035 2 View

Which is suitable for use with Python? MySQL or SQL Server?

Which is suitable for use with Python? MySQL or SQL Server? What is your suggestion?

01 March 2021 3,422 3 View

How can I make stacked bar graph with scatter plot?

I want to make a stacked bar graph with showing each data value as dots. I tried with graph pad prism, version 6, but could not succeed. Does anyone have tried before making such graphs?

01 March 2021 9,383 1 View

What could be reason for getting such type of graph for complex impedance in case of polymer blend films?

Its effect appears in real part of ac conductivity also. Can anyone suggest any reason behind it?

26 February 2021 3,487 3 View

How to plot the probability paper of Gumbel distribution using R programing?

In R-studio, there are many commands of Gumbel package. Arguments are also different. I`m asking about the alpha parameter of the Copula which must be greater than 1. If this is the one used to...

25 February 2021 5,229 3 View

Can I use a graph from a another source in a thesis?

I have a permission from X company to use their graph from a report, but they have a reference in the bottom left corner of the graph as follows: "Source: Database Y". Is it OK to use this graph...

24 February 2021 2,269 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View